Hotpoint RVM5160MPSA Installation Instructions
Hotpoint RVM5160MPSA Manual
 |
View all Hotpoint RVM5160MPSA manuals
Add to My Manuals
Save this manual to your list of manuals |
Hotpoint RVM5160MPSA manual content summary:
- Hotpoint RVM5160MPSA | Installation Instructions - Page 1
. • IMPORTANT - Observe all governing codes and ordinances. • Note to Installer - Be sure to leave these instructions with the Consumer. • Note to Consumer - Keep these instructions for future reference. • Skill level - Installation of this appliance requires basic mechanical and electrical skills - Hotpoint RVM5160MPSA | Installation Instructions - Page 2
could result in minor or moderate injury. IMPORTANT SAFETY INSTRUCTIONS A qualified electrician must perform a ground continuity check on YOUR SAFETY: CAUTION For personal safety, the mounting surface must be capable of supporting the cabinet load, in addition to the added weight of this 63-85 - Hotpoint RVM5160MPSA | Installation Instructions - Page 3
Installation Instructions HOOD EXHAUST NOTE: Read these next two pages only if you plan to vent your exhaust to the outside. If you plan to recirculate the - Hotpoint RVM5160MPSA | Installation Instructions - Page 4
Installation Instructions NOTE: If you need to install ducts, note that the total duct length of 31»4Ǝ[ƎUHFWDQJXODURUƎGLDPHWHUURXQG duct should not exceed 140 equivalent - Hotpoint RVM5160MPSA | Installation Instructions - Page 5
the power cord) ADDITIONAL PARTS Part Top Cabinet Template Quantity 1 Rear Wall 1 Template Installation 1 Instructions Separately 2 Packed Grease Filter Mounting Plate 1 (for supporting the microwave Oven) Cover plate (for 1 Room Venting installation) You will find the installation - Hotpoint RVM5160MPSA | Installation Instructions - Page 6
ƎRU between the microwave oven and the cabinets. Your more from the Owner's Manual contains the kit number for your Ǝ min. cooking surface model. • If you oven beneath smooth, flat cabinets, be careful to follow the instructions on the top cabinet template for power cord clearance. • - Hotpoint RVM5160MPSA | Installation Instructions - Page 7
1 PLACEMENT OF THE MOUNTING PLATE A. REMOVING THE MICROWAVE OVEN FROM THE CARTON 1 Remove the installation instructions, filters, glass tray, mounting plate, and the small hardware bag. Do not remove the foam protecting the front of the oven. 2 Fold back all 4 carton - Hotpoint RVM5160MPSA | Installation Instructions - Page 8
Installation Instructions C DETERMINING MOUNTING PLATE LOCATION UNDER YOUR CABINET Plate Position - beneath flat bottom cabinet Plate Position - beneath framed recessed cabinet bottom Draw a vertical line on the - Hotpoint RVM5160MPSA | Installation Instructions - Page 9
use at least one wood screw mounted firmly in a stud to support the weight of the microwave. Mark two additional, evenly spaced locations for 4. Remove the template from the rear wall. 5. Review the Installation Instruction book for your installation situation. Darle vuelta a la hoja para consultar - Hotpoint RVM5160MPSA | Installation Instructions - Page 10
HOLES OPTION 2: USE METAL BRACKET AS TEMPLATE NOTE: Refer to step C "DETERMINING MOUNTING PLATE LOCATION UNDER YOUR CABINET on page 8 for aligning instructions. STEP 1: Draw a vertical line on the wall at the center of the 30" space. STEP 4: Installer uses a level to draw a horizontal line - Hotpoint RVM5160MPSA | Installation Instructions - Page 11
Installation Instructions 2 INSTALLATION TYPES (Choose A, B or C) This microwave oven is designed for adaptation to the following Kit is required for the non-vented exhaust. (See your Owner's Manual for the kit number.) C OUTSIDE BACK EXHAUST (HORIZONTAL DUCT) See page 20 31-7000091 Rev. 2 11 - Hotpoint RVM5160MPSA | Installation Instructions - Page 12
. A2 USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws and a hole large enough for the power cord to fit through. • Read the instructions on the TOP CABINET TEMPLATE. • Tape it underneath the top cabinet. • Drill the holes, following the - Hotpoint RVM5160MPSA | Installation Instructions - Page 13
Installation Instructions A3. CHECK BLOWER MOTOR ORIENTATION The blower fan blade opening should be facing the front of the microwave. You will have to remove the top - Hotpoint RVM5160MPSA | Installation Instructions - Page 14
Installation Instructions A4. ADAPTING BLOWER FOR RECIRCULATION (continued) 5 Place the blower unit back into the opening. CAUTION Do not pull or stretch the blower unit wiring. Make - Hotpoint RVM5160MPSA | Installation Instructions - Page 15
Installation Instructions A4. MOUNT THE OVEN (continued) 3 Attach the oven to the Slide the grille to the left and forward to remove. Charcoal Filter 5 Install grease filters. See the Owner's Manual packed with the oven. 4 Slide the old filter down and out to remove it. 5 Remove plastic and other - Hotpoint RVM5160MPSA | Installation Instructions - Page 16
use at least one wood screw mounted firmly in a stud to support the weight of the microwave. Mark two additional, evenly spaced locations for 4. Remove the template from the rear wall. 5. Review the Installation Instruction book for your installation situation. Darle vuelta a la hoja para consultar - Hotpoint RVM5160MPSA | Installation Instructions - Page 17
Installation Instructions B2 USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adaptor. 2 Slide the blower plate from under - Hotpoint RVM5160MPSA | Installation Instructions - Page 18
Installation Instructions B4. ADAPTING BLOWER FOR OUTSIDE VENTILATION (continued) 5 Place the blower unit back into the opening. CAUTION Do not pull or stretch the blower unit wiring. - Hotpoint RVM5160MPSA | Installation Instructions - Page 19
Installation Instructions B6. MOUNT THE OVEN (continued) Cabinet Front Cabinet Bottom Shelf the oven in place against the wall and the top cabinet.) 5 Install grease filters. See the Owner's Manual packed with the oven. 1 Extend the house duct down to connect to the exhaust adaptor. 2 Seal exhaust - Hotpoint RVM5160MPSA | Installation Instructions - Page 20
to use at least one wood screw mounted firmly in a stud to support the weight of the microwave. Mark two additional, evenly spaced locations for holes A and B in the mounting plate. • Cut the opening, following the instructions of the REAR WALL TEMPLATE. C2 ATTACH THE MOUNTING PLATE TO THE WALL D - Hotpoint RVM5160MPSA | Installation Instructions - Page 21
Installation Instructions C3. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws and a hole large enough for the power cord to fit through. C4. ADAPTING BLOWER FOR OUTSIDE BACK EXHAUST 1 Remove and save the two screws - Hotpoint RVM5160MPSA | Installation Instructions - Page 22
Installation Instructions 5 Locate the two "knockout" plates, on the rear oven panel, near the top of the oven. Using tin snips, carefully cut the web area from - Hotpoint RVM5160MPSA | Installation Instructions - Page 23
Installation Instructions Cabinet Front Cabinet Bottom Shelf Filler Block Equivalent to Depth of Cabinet Recess Self-Aligning Screw Oven Top , hold the oven in place against the wall and the top cabinet.) 5 Install grease filters. See the Owner's Manual packed with the oven. 31-7000091 Rev. 2 23 - Hotpoint RVM5160MPSA | Installation Instructions - Page 24
BEFORE YOU USE YOUR MICROWAVE 1. Make sure the microwave oven has been installed according to instructions. 6. Read the Owner's Manual. 2. Remove all packing material from the microwave oven. 3. Install turntable and ring in cavity. 4. Replace house fuse or turn breaker back on. 7. KEEP - Hotpoint RVM5160MPSA | Installation Instructions - Page 25
Instrucciones Horno microondas para colocar encima de la de instalación estufa ANTES DE EMPEZAR Lea estas instrucciones completa y cuidadosamente. • IMPORTANTE - Guarde estas instrucciones para el uso del inspector local. • IMPORTANTE - Cumpla con todos los códigos y ordenanzas gubernamentales. • - Hotpoint RVM5160MPSA | Installation Instructions - Page 26
Instrucciones de Instalación INSTRUCCIONES DE SEGURIDAD IMPORTANTES Éste es el símbolo de alerta de seguridad. El mismo alerta sobre potenciales riesgos que le pueden producir la muerte o lesiones tanto a usted como a otras personas. Todos los mensajes de seguridad estarán a continuación del sí - Hotpoint RVM5160MPSA | Installation Instructions - Page 27
Instrucciones de Instalación CAMPANA DE ESCAPE NOTA: Lea las siguientes dos páginas solamente si planea ventilar el escape hacia el exterior. Si por el contrario planea recircular el aire de vuelta hacia el salón, continúe en la página 30. ESCAPE SUPERIOR EXTERNO (EJEMPLO SOLAMENTE) La siguiente - Hotpoint RVM5160MPSA | Installation Instructions - Page 28
Instrucciones de Instalación NOTA: Si usted necesita instalar conductos, tenga pendiente que la longitud total del conducto rectangular de 31»4Ǝ[ƎRHOFRQGXFWRUHGRQGRGHƎGHGLiPHWURno debe sobrepasar 140 pies equivalentes. La ventilación externa requiere un CONDUCTO DE CAMPANA DE ESCAPE. - Hotpoint RVM5160MPSA | Installation Instructions - Page 29
Instrucciones de Instalación DAÑO - ENVÍO/ INSTALACIÓN • Si la unidad se daña durante el envío, devuelva la unidad a la tienda donde fue comprada para su reparación o reemplazo. • Si la unidad es dañada por el cliente, la reparación o reemplazo es responsabilidad del cliente. • Si la unidad es dañ - Hotpoint RVM5160MPSA | Installation Instructions - Page 30
PiV a partir de la superficie de la un Kit de panel de relleno para llenar el espacio entre el horno de microondas y los gabinetes. Su manual del propietario contiene el número de kit para su modelo. estufa • Si usted se dispone a ventilar su horno hacia el exterior, ver Protector posterior de - Hotpoint RVM5160MPSA | Installation Instructions - Page 31
Instrucciones de Instalación 1 CÓMO COLOCAR EL PLATO DE MONTAJE A. CÓMO REMOVER EL HORNO DEL EMBALAJE / CÓMO REMOVER EL PLATO DE MONTAJE 1 Remueva la caja que contiene las instrucciones de instalación, los filtros, el adaptador de escape, el regulador de tiro, estante y la pequeña bolsa con los - Hotpoint RVM5160MPSA | Installation Instructions - Page 32
Instrucciones de Instalación C DETERMINACIÓN DE LA UBICACIÓN DE LA PLACA DE MONTAJE DEBAJO DE SU GABINETE Posición de la Placa - debajo del gabinete inferior plano Posición de la Placa - debajo del gabinete inferior empotrado con marco Dibuje una línea vertical en la pared en el centro del - Hotpoint RVM5160MPSA | Installation Instructions - Page 33
use at least one wood screw mounted firmly in a stud to support the weight of the microwave. Mark two additional, evenly spaced locations for 4. Remove the template from the rear wall. 5. Review the Installation Instruction book for your installation situation. Darle vuelta a la hoja para consultar - Hotpoint RVM5160MPSA | Installation Instructions - Page 34
Instrucciones de Instalación D MARCA DE LOS AGUJEROS DE MONTAJE OPCIÓN 2: USE EL SOPORTE METÁLICO COMO PLANTILLA NOTA: Para acceder a instrucciones de alineación, consulte el paso C "DETERMINACIÓN DE LA UBICACIÓN DE LA PLACA DE MONTAJE DEBAJO DE SU GABINETE" en la página 8. PASO 1: Dibuje una lí - Hotpoint RVM5160MPSA | Installation Instructions - Page 35
el escape superior exterior Ver página 12 Un Kit de accesorios de filtro de carbonilla es necesario para el sistema sin ventilación. (Consulte su Manual del Propietario para obtener el número del kit.) Ver página 16 C ESCAPE POSTERIOR EXTERIOR (CONDUCTO HORIZONTAL) Ver página 20 31-7000091 Rev - Hotpoint RVM5160MPSA | Installation Instructions - Page 36
use at least one wood screw mounted firmly in a stud to support the weight of the microwave. Mark two additional, evenly spaced locations for 4. Remove the template from the rear wall. 5. Review the Installation Instruction book for your installation situation. Darle vuelta a la hoja para consultar - Hotpoint RVM5160MPSA | Installation Instructions - Page 37
Instrucciones de Instalación A3. CONTROLE LA ORIENTACIÓN DEL MOTOR DEL CALEFACTOR La abertura de la cuchilla del flan del soplador debe estar orientada hacia el frente del microondas. Deberá quitar la placa de cubierta superior para verificar la orientación de las aspas del ventilador. Si la - Hotpoint RVM5160MPSA | Installation Instructions - Page 38
Instrucciones de Instalación A4. CÓMO ADAPTAR EL CALEFACTOR PARA LA RECIRCULACIÓN (continuación) 5 Coloque la unidad del calefactor de nuevo en la abertura. PRECAUCIÓN No tire ni estire los cables del calefactor. Cerciórese de que los alambres no están pellizcados. NOTA: Cuando se encuentre - Hotpoint RVM5160MPSA | Installation Instructions - Page 39
los tornillos, mantenga el horno en su lugar contra la pared y el gabinete superior.) Filtro de carbonilla 5 Instale los filtros de grasa. Ver el Manual del Propietario que viene con el horno. 4 Deslice el filtro viejo hacia el frente del horno y retírelo. 5 Retire el plástico y la envoltura - Hotpoint RVM5160MPSA | Installation Instructions - Page 40
use at least one wood screw mounted firmly in a stud to support the weight of the microwave. Mark two additional, evenly spaced locations for 4. Remove the template from the rear wall. 5. Review the Installation Instruction book for your installation situation. Darle vuelta a la hoja para consultar - Hotpoint RVM5160MPSA | Installation Instructions - Page 41
Instrucciones de Instalación B2. USE LA PLANTILLA DEL GABINETE SUPERIOR PARA LA PREPARACIÓN DEL GABINETE Deberá perforar agujeros para los tornillos de apoyo superiores, un agujero suficientemente grande para que el cable eléctrico quepa, y un recorte lo suficientemente grande como para que el - Hotpoint RVM5160MPSA | Installation Instructions - Page 42
Instrucciones de Instalación B4. CALEFACTOR PARA LA VENTILACIÓN EXTERNA (cont.) 5 Vuelva a colocar la unidad del calefactor en la abertura. PRECAUCIÓN No empuje ni extienda el cableado de la unidad del calefactor. Asegúrese de que los cables no posean cortes. 6 Vuelva a colocar los tornillos del - Hotpoint RVM5160MPSA | Installation Instructions - Page 43
conectarlo con el adaptador de escape. 2 Selle las juntas del conducto de escape usando cinta adhesiva de conductos. 5 Instale los filtros de grasa. Ver el Manual del Propietario que viene con el horno. 31-7000091 Rev. 2 19 - Hotpoint RVM5160MPSA | Installation Instructions - Page 44
use at least one wood screw mounted firmly in a stud to support the weight of the microwave. Mark two additional, evenly spaced locations for 4. Remove the template from the rear wall. 5. Review the Installation Instruction book for your installation situation. Darle vuelta a la hoja para consultar - Hotpoint RVM5160MPSA | Installation Instructions - Page 45
Instrucciones de Instalación C3. USE LA PLANTILLA DEL GABINETE SUPERIOR PARA PREPARAR EL GABINETE SUPERIOR Necesita perforar agujeros para los tornillos de apoyo superiores y un agujero suficientemente grande para que el cable eléctrico quepa. C4. CÓMO ADAPTAR EL CALEFACTOR PARA EL ESCAPE - Hotpoint RVM5160MPSA | Installation Instructions - Page 46
Instrucciones de Instalación 5 Localice los dos platos removibles en el panel posterior del horno, cerca de la parte superior del horno. Usando tijeras, cuidadosamente corte el área de telaraña de los dos agujeros lado a lado (que aseguran los platos removibles al horno). Corte las cuatro telarañas - Hotpoint RVM5160MPSA | Installation Instructions - Page 47
horno superior. (Mientras aprieta los tornillos, mantenga el horno en su lugar contra la pared y el gabinete superior.) 5 Instale los filtros de grasa. Ver el Manual del Propietario que viene con el horno. 31-7000091 Rev. 2 23 - Hotpoint RVM5160MPSA | Installation Instructions - Page 48
Instrucciones de Instalación ANTES DE USAR EL HORNO MICROONDAS 1 Asegúrese de que el horno microondas haya sido instalado de acuerdo con las instrucciones. 6 Lea la sección de Uso y Cuidado Rápido. USQEU&ICCKARE 2 Retire todos los materiales de embalaje del horno microondas. 3 Instale el
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
 |
 |
READ CAREFULLY.
KEEP THESE INSTRUCTIONS
.
Installation
Over the Range
Instructions
Microwave Oven
Read these instructions completely and carefully.
•
IMPORTANT
–
Save these
instructions for local inspector’s use.
•
IMPORTANT
–
Observe all
governing codes and ordinances.
•
Note to Installer
–
Be sure to leave these
instructions with the Consumer.
BEFORE YOU BEGIN
•
Note to Consumer
–
Keep these
instructions for future reference.
•
Skill level
– Installation of this appliance requires
basic mechanical and electrical skills.
•
Proper installation is the responsibility of the installer.
•
Product failure due to improper installation is not
covered under the Warranty.
31-7000091
Rev. 2
09-20
GEA
English/Spanish