Hotpoint RVM5160MPSA Installation Instructions - Page 18

Assemble And, Install Adaptor, Mount The Oven, Adapting Blower For, Outside Ventilation

Get Hotpoint RVM5160MPSA PDF manuals and user guides View all Hotpoint RVM5160MPSA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Installation Instructions B4. ADAPTING BLOWER FOR OUTSIDE VENTILATION (continued) 5 Place the blower unit back into the opening. CAUTION Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched. 3 Attach the exhaust adaptor to the blower plate with the two bronze metal screws provided. Make sure that the damper pivots easily before mounting oven. You will need to make adjustments to assure proper alignment with your house exhaust duct after the oven is installed. B6. MOUNT THE OVEN 6 Replace blower motor screws removed in Step 2. Slide cover plate into position on the back of the unit. Replace blower plate and screws removed in Step 1. Blower Plate Screws Blower Plate Back of Oven Blower Motor Screws Cover Plate B5. ASSEMBLE AND INSTALL ADAPTOR Damper Exhaust Adaptor Blower Plate Back of Oven Cover Plate NOTE: On some models, the exhaust adaptor and damper assembly may already be assembled to the oven. 1 Place the oven in its upright position, with the top of the unit facing up. NOTE: Make sure the blower fan blades are visible and are pointing up. 2 Insert the tabs on each side of the damper into the holes at the inside rear of the adaptor. 18 FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS OVEN. IMPORTANT: Do not grip or use handle during installation. NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord. NOTE: We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf. IMPORTANT: If filler blocks are not used, case damage may occur from over tightening screws. NOTE: When mounting the microwave, thread power cord through hole in bottom of top cabinet. Keep it tight throughout Steps 1-3. Do not pinch cord or lift microwave oven by pulling cord. 1 Lift microwave, tilt it forward, and hook slots at back bottom edge onto four lower tabs of mounting plate. Power Cord 2 Rotate front of microwave oven up against cabinet bottom. 31-7000091 Rev. 2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
18
31-7000091
Rev. 2
Installation Instructions
ASSEMBLE AND
INSTALL ADAPTOR
MOUNT THE OVEN
B6.
B5.
FOR EASIER INSTALLATION AND PERSONAL
SAFETY, WE RECOMMEND THAT
TWO PEOPLE
INSTALL THIS OVEN.
IMPORTANT: Do not grip or use handle
during installation.
NOTE:
If your cabinet is metal, use the nylon
grommet around the power cord hole to prevent
cutting of the cord.
NOTE:
We recommend using filler blocks if the
cabinet front hangs below the cabinet bottom shelf.
IMPORTANT: If filler blocks are not
used, case damage may occur from over
tightening screws.
Damper
Back of
Oven
Cover Plate
Place the oven in its upright position, with the top of
the unit facing up.
NOTE: Make sure the blower fan blades are
visible and are pointing up.
Insert the tabs on each side of the damper into the
holes at the inside rear of the adaptor.
Exhaust
Adaptor
1
2
Blower Plate
NOTE:
On some models, the exhaust adaptor and
damper assembly may already be assembled to the
oven.
Place the blower unit back into the opening.
CAUTION
Do not pull or stretch the
blower unit wiring. Make sure the wires are
not pinched.
6
5
Replace blower motor screws removed in Step 2.
Slide cover plate into position on the back of the
unit. Replace blower plate and screws removed in
Step 1.
Blower Plate
Back of
Oven
Blower Plate Screws
Blower Motor Screws
ADAPTING BLOWER FOR
OUTSIDE VENTILATION
(continued)
B4.
Attach the exhaust adaptor to the blower plate
with the two bronze metal screws provided.
Make sure that the damper pivots easily before
mounting oven.
You will need to make adjustments to assure
proper alignment with your house exhaust duct
after the oven is installed.
3
Cover Plate
NOTE:
When mounting the microwave, thread
power cord through hole in bottom of top cabinet.
Keep it tight throughout Steps 1–3. Do not pinch
cord or lift microwave oven by pulling cord.
Lift microwave, tilt it forward, and hook slots
at back bottom edge onto four lower tabs of
mounting plate.
Rotate front of microwave oven up against
cabinet bottom.
1
2
Power Cord