Hotpoint RVM5160MPSA Installation Instructions - Page 40

Instrucciones de Instalación B VENTILACIÓN SUPERIOR EXTERIOR (Conducto Vertical) VISIÓN GENERAL DE LA INSTALACIÓN B1. Adjunte la Placa de Montaje a la Pared B2. Prepare el Gabinete Superior B3. Ajuste el Motor del Calentador B4. Ventilación Externa B5. Nstalación Del Adaptador B6. Montar El Horno B7. Cómo Ajustar El Adaptador De Escape B8. Cómo Conectar B El Conducto OPTION 1 NOTE: IT IS VERY IMPORTANT TO READ AND FOLLOW THE DIRECTIONS IN THE INSTALLATION INSTRUCTIONS BEFORE PROCEEDING WITH THIS REAR WALL TEMPLATE. This Rear Wall Template serves to position the bottom mounting plate and to locate the horizontal exhaust outlet. 1. Use a level to check that the template is positioned accurately. 2. Locate and mark at least one stud on the left or right side of the centerline. NOTE:It is important to use at least one wood screw mounted firmly in a stud to support the weight of the microwave. Mark two additional, evenly spaced locations for the supplied toggle bolts. 3. Drill holes in the marked locations. Where there is a stud, drill a 3/16" hole for wood screws. For holes that do not line up with a stud, drill 5/8" holes for toggle bolts. NOTE::DO NOT INSTALL THE MOUNTING PLATE AT THIS TIME. 4. Remove the template from the rear wall. 5. Review the Installation Instruction book for your installation situation. Darle vuelta a la hoja para consultar la versión en Español. Locate and mark holes to align with holes in the mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY SPACED TOGGLE BOLTS IN THE MOUNTING PLATE AREA. Trim the rear wall template along the dotted line. 3/8" TO EDGE 12" F. CUT OUT FOR HORIZONTAL 4" OUTSIDE EXHAUST CUT HOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR CAUTION - IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE RECOMMENDED DIMENSION, GREASE-LADEN AIR WILL DISCHARGE INTO HOUSE STRUCTURE 30" MINIMUM WIDTH REQUIRED REAR WALL TEMPLATE C D B OPTION 2 STEP 1: Installer uses bracket to make 2 marks. First mark is made by using the stampled slot in bracket. Second mark is made on the ouside edge of bracket. Horizontal line Make a mark here, even with bottom of stamped slot Make a mark here, along inside bottom of the stamped slot provided. STEP 4: STEP 2: Installer moves bracket to the other side of the cabinets and makes 2 more marks. Marks are the same as STEP 1, just opposite side. Make a mark here, along inside bottom of the stamped slot provided (same as Step 1). Make a mark here, even with bottom of stamped slot NOTES: - 13" Max Cabinet Depth - 15" deep cabinets require additional steps using an additional installation kit: JX36BUMP C A A C D IMPORTANTE: NO retire los espaciadores de cartón entre el protector de calor y la puerta. B1 ADHIERA LA PLACA DE MONTAJE A LA PARED PARA USAR TORNILLOS CON RESORTE: Placa de Montaje Espacio para Tornillos con Resorte Superior al Grosor de la Pared Tuercas Mariposa Tornillo con Resorte D B A C Adhiera la placa a la pared usando tornillos con resortes. Por lo menos un tornillo de madera deberá ser usado para adherir la placa al montaje de pared. Las ubicaciones recomendadas sobre la placa de pared están indicadas por A, B, C y D. 1 Retire las tuercas mariposa de los tornillos. 2 Inserte los tornillos en la placa de montaje a través de los agujeros designados para entrar en la placa de yeso y vuelva a ajustar las tuercas mariposa a 3/4" sobre cada tornillo. Pared Placa de Montaje Extremo del Tornillo 3 Inserte las tuercas mariposa en los agujeros de la pared y coloque la placa de montaje contra la pared. PRECAUCIÓN Tenga cuidado para evitar pellizcos en los dedos entre la parte trasera de la placa de montaje y la pared. 4 Ajuste todos los tornillos. Empuje la placa hacia afuera de la pared para ayudar a ajustar los tornillos. 16 31-7000091 Rev. 2