Husqvarna 572 XP G Owner Manual - Page 23

To do a check of the chain brake, To do a check of the throttle trigger and, throttle trigger

Get Husqvarna 572 XP G PDF manuals and user guides View all Husqvarna 572 XP G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

2. Make sure that the front hand guard moves freely and that it is attached safely to the clutch cover. To do a check of the throttle trigger and throttle trigger lockout 1. Make sure that the throttle trigger and throttle trigger lockout move freely and that the return spring works correctly. 3. Hold the product with 2 hands above a stump or other stable surface. WARNING: The engine must be off. 4. Let go of the front handle and let the guide bar tip fall against the stump. 2. Press down the throttle trigger lockout and make sure that it goes back to its initial position when you release it. 3. Make sure that the throttle trigger is locked at the idle position when the throttle trigger lockout is released. 5. Make sure that the chain brake engages as the guide bar tip hits the stump. To do a check of the chain brake 1. Start the product. Refer to To start the product on page 13 for instructions. WARNING: Make sure that the saw chain does not touch the ground or other objects. 2. Hold the product tightly. 3. Apply full throttle and tilt your left wrist against the front hand guard to engage the chain brake. The saw chain must stop immediately. 4. Start the product and apply full throttle. 5. Release the throttle trigger and make sure that the saw chain stops and stays stationary. WARNING: If the saw chain rotates when the throttle trigger is in the idle position, speak to your servicing dealer. To do a check of the chain catcher 1. Make sure that there is no damage on the chain catcher. 2. Make sure that the chain catcher is stable and attached to the body of the product. WARNING: Do not let go of the front handle. 140 - 007 - 04.06.2020 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
2.
Make sure that the front hand guard moves freely
and that it is attached safely to the clutch cover.
3.
Hold the product with 2 hands above a stump or
other stable surface.
WARNING:
The engine must be off.
4.
Let go of the front handle and let the guide bar tip fall
against the stump.
5.
Make sure that the chain brake engages as the
guide bar tip hits the stump.
To do a check of the chain brake
1.
Start the product. Refer to
To start the product on
page 13
for instructions.
WARNING:
Make sure that the saw
chain does not touch the ground or other
objects.
2.
Hold the product tightly.
3.
Apply full throttle and tilt your left wrist against the
front hand guard to engage the chain brake. The
saw chain must stop immediately.
WARNING:
Do not let go of the front handle.
To do a check of the throttle trigger and
throttle trigger lockout
1.
Make sure that the throttle trigger and throttle trigger
lockout move freely and that the return spring works
correctly.
2.
Press down the throttle trigger lockout and make
sure that it goes back to its initial position when you
release it.
3.
Make sure that the throttle trigger is locked at the
idle position when the throttle trigger lockout is
released.
4.
Start the product and apply full throttle.
5.
Release the throttle trigger and make sure that the
saw chain stops and stays stationary.
WARNING:
If the saw chain rotates
when the throttle trigger is in the idle
position, speak to your servicing dealer.
To do a check of the chain catcher
1.
Make sure that there is no damage on the chain
catcher.
2.
Make sure that the chain catcher is stable and
attached to the body of the product.
140 - 007 - 04.06.2020
23