Husqvarna EZ4824 Owners Manual - Page 33

Manual Transport, ZT-2800 Bypass Linkages, Pump Release Valves

Get Husqvarna EZ4824 PDF manuals and user guides View all Husqvarna EZ4824 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

operation Manual Transport ZT-2800 Bypass Linkages When pushing or pulling the mower, engage the ZT-2800 (Integrated Zeroturn Transaxle) bypass linkages. The ZT-2800 bypass linkages are located on the rear of the frame, below the rear engine guard. 1. Raise the deck into the highest cutting position. 2. Pull the ZT-2800 bypass linkages up and out of the keyhole slots. Release the levers with the head outside the frame and held in the bypass position. 3. To reengage the ZT-2800 to drive, reverse the above procedure. Load the machine into truck or trailer by driving up ramps in low gear. DO NOT LIFT! The machine is not intended to be lifted by hand. Bypass linkage, ZT-2800 engaged 8058-032 WARNING! Make no adjustments without: • the engine stopped, • the ignition key removed, • the parking brake activated Pump Release Valves Pump release valves are located at the left and right of the pump. They are used to release the system so the machine may be moved by hand when not running. Tilt seat forward to gain access to the pump. The left bypass valve sits directly opposite the right valve. It is not visible in the illustration. Use a 17 mm open end wrench or socket and ratchet. Turn the outer locknut 2-3 turns. Using an 8mm wrench or socket, turn the inner nut one turn. Reverse the procedure to reset the pump, makng sure the outer locknut is tightened. 8058-032 Bypass linkage, ZT-2800 locked in the bypass position IMPORTANT INFORMATION Tighten the valve moderately. Do not overtighten the valve when closing. That can damage the valve seat. Pump release valve - right 8011-507 Husqvarna-33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
OPERATION
Husqvarna-
33
Pump Release Valves
Pump release valves are located at the left and right of
the pump. They are used to release the system so the
machine may be moved by hand when not running.
Tilt seat forward to gain access to the pump. The left
bypass valve sits directly opposite the right valve. It is
not visible in the illustration.
Use a 17 mm open end wrench or socket and ratchet.
Turn the outer locknut 2-3 turns. Using an 8mm
wrench or socket, turn the inner nut one turn.
Reverse the procedure to reset the pump, makng sure
the outer locknut is tightened.
IMPORTANT INFORMATION
Tighten the valve moderately.
Do not overtighten the valve when closing.
That can damage the valve seat.
8011-507
Pump release valve - right
Manual Transport
ZT-2800 Bypass Linkages
When pushing or pulling the mower, engage the
ZT-2800 (Integrated Zeroturn Transaxle) bypass
linkages. The ZT-2800 bypass linkages are located on
the rear of the frame, below the rear engine guard.
Raise the deck into the highest cutting position.
1.
Pull the ZT-2800 bypass linkages up and out of
2.
the keyhole slots. Release the levers with the
head outside the frame and held in the bypass
position.
To reengage the ZT-2800 to drive, reverse the
3.
above procedure.
Load the machine into truck or trailer by driving up
ramps in low gear. DO NOT LIFT! The machine is not
intended to be lifted by hand.
8058-032
Bypass linkage, ZT-2800 engaged
8058-032
Bypass linkage, ZT-2800 locked in the bypass position
WARNING!
Make no adjustments without:
the engine stopped,
•
the ignition key removed,
•
the parking brake activated
•