Husqvarna L321AH Owner Manual - Page 13

Assembly

Get Husqvarna L321AH PDF manuals and user guides View all Husqvarna L321AH manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Safety instructions for maintenance WARNING: Read the warning instructions that follow before you use the product. • The exhaust fumes from the engine contain carbon monoxide, an odourless, poisonous and very dangerous gas. Do not start the engine indoors or in closed spaces. • Before you do the maintenance on the product, stop the engine and remove the ignition cable from the spark plug. • Use protective gloves when you do maintenance on the cutting equipment. The blade is very sharp and cuts can easily occur. • Accessories and changes to the product that are not approved by the manufacturer, can cause serious injury or death. Do not change the product. Always use accessories that are approved by the manufacturer. • If the maintenance is not done correctly and regularly, the risk of injury and damage to the product increases. • Only do the maintenance as given in this owner's manual. All other servicing must be done by an approved Husqvarna service agent. • Let an approved Husqvarna service agent do servicing on the product regularly. • Replace damaged, worn or broken parts. Assembly Introduction WARNING: Before you assemble the product, you must read and understand the safety chapter. To install the starter rope handle 1. Attach the loop for the starter rope and the T-knob. Do not tighten fully. WARNING: Remove the spark plug cable from the spark plug before you assemble the product. To assemble the handle 1. Lift the lower handle. 2. Hold the engine brake handle against the handlebar. 3. Slowly pull out the starter rope and put it into the loop for the starter rope. 4. Tighten the T-knob. 2. Align the holes at the bottom of the lower handle with the holes in the handle brackets. Note: Select the holes that give the best operation position. 3. Tighten the lower handle knobs. 4. Lift the upper handle and align it with the lower handle. 5. Tighten the upper handle knobs fully. To set the product in transport position 1. Remove the grass catcher. 1240 - 001 - 08.07.2019 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Safety instructions for maintenance
WARNING:
Read the warning instructions
that follow before you use the product.
•
The exhaust fumes from the engine contain carbon
monoxide, an odourless, poisonous and very
dangerous gas. Do not start the engine indoors or in
closed spaces.
•
Before you do the maintenance on the product, stop
the engine and remove the ignition cable from the
spark plug.
•
Use protective gloves when you do maintenance on
the cutting equipment. The blade is very sharp and
cuts can easily occur.
•
Accessories and changes to the product that are not
approved by the manufacturer, can cause serious
injury or death. Do not change the product. Always
use accessories that are approved by the
manufacturer.
•
If the maintenance is not done correctly and
regularly, the risk of injury and damage to the
product increases.
•
Only do the maintenance as given in this owner's
manual. All other servicing must be done by an
approved Husqvarna service agent.
•
Let an approved Husqvarna service agent do
servicing on the product regularly.
•
Replace damaged, worn or broken parts.
Assembly
Introduction
WARNING:
Before you assemble the
product, you must read and understand the
safety chapter.
WARNING:
Remove the spark plug cable
from the spark plug before you assemble the
product.
To assemble the handle
1.
Lift the lower handle.
2.
Align the holes at the bottom of the lower handle with
the holes in the handle brackets.
Note:
Select the holes that give the best operation
position.
3.
Tighten the lower handle knobs.
4.
Lift the upper handle and align it with the lower
handle.
5.
Tighten the upper handle knobs fully.
To install the starter rope handle
1.
Attach the loop for the starter rope and the T-knob.
Do not tighten fully.
2.
Hold the engine brake handle against the handlebar.
3.
Slowly pull out the starter rope and put it into the
loop for the starter rope.
4.
Tighten the T-knob.
To set the product in transport position
1.
Remove the grass catcher.
1240 - 001 - 08.07.2019
7