Husqvarna ST 427 Owner Manual - Page 19

To inspect the augers and the, scraper bar, To replace the auger shear pins, To replace the impeller

Get Husqvarna ST 427 PDF manuals and user guides View all Husqvarna ST 427 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

c) Make sure that the air filter is clean. • If the spark plug is dirty, clean it and make sure that the electrode gap is correct, refer to Technical data on page 29. 5. Put the ON/OFF key in the ignition and connect the spark plug cable to the spark plug. To replace the impeller shear pins The impeller shear pins protect the product from damage. The impeller shear pins break if an object comes into the moving parts. • Replace the spark plug if it is necessary. To inspect the augers and the scraper bar 1. Before each use, inspect the augers and the scraper bar for wear. 2. If the edge of the scraper bar is worn, reverse the scraper bar. If the scraper bar has damages or is worn on both edges, replace it. 3. If the edges of the augers are worn, contact an authorized service center to replace them. To replace the auger shear pins The auger shear pins protect the product from damage. The auger shear pins break if an object comes into the moving parts. CAUTION: Use only original equipment shear pins supplied with the product. 1. If an auger shear pin breaks, stop the engine and wait for the moving parts to stop. 2. Remove the ON/OFF key and disconnect the spark plug cable. 3. Align the hole in the auger hub (B) with the hole in the auger shaft (C) and install a new ¼ - 20 x 2 shear pin (A). 4. Install a ¼-20 locknut (D) on the shear pin and tighten. A CAUTION: Use only original equipment shear pins supplied with the product. 1. If an impeller shear pin breaks, stop the engine and wait for the moving parts to stop. 2. Remove the ON/OFF key and disconnect the spark plug cable. 3. Align the hole in the impeller hub (A) with the holes in the impeller shaft (B) and install a new ¼-20 shear pin (C). 4. Install a ¼-20 locknut (D) on the shear pin and tighten. C B A D 5. Put the ON/OFF key in the ignition and connect the spark plug cable to the spark plug. To replace the fuse The fuse holders are installed behind the battery cover. B D B C 876 - 011 - 11.05.2020 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
c)
Make sure that the air filter is clean.
•
If the spark plug is dirty, clean it and make sure
that the electrode gap is correct, refer to
Technical data on page 29
.
•
Replace the spark plug if it is necessary.
To inspect the augers and the
scraper bar
1.
Before each use, inspect the augers and the
scraper bar for wear.
2.
If the edge of the scraper bar is worn, reverse the
scraper bar. If the scraper bar has damages or is
worn on both edges, replace it.
3.
If the edges of the augers are worn, contact an
authorized service center to replace them.
To replace the auger shear pins
The auger shear pins protect the product from
damage. The auger shear pins break if an object
comes into the moving parts.
CAUTION:
Use only original equipment
shear pins supplied with the product.
1.
If an auger shear pin breaks, stop the engine and
wait for the moving parts to stop.
2.
Remove the ON/OFF key and disconnect the
spark plug cable.
3.
Align the hole in the auger hub (B) with the hole
in the auger shaft (C) and install a new ¼ - 20 x 2
shear pin (A).
4.
Install a ¼-20 locknut (D) on the shear pin and
tighten.
A
B
D
B
C
5.
Put the ON/OFF key in the ignition and connect
the spark plug cable to the spark plug.
To replace the impeller shear pins
The impeller shear pins protect the product from
damage. The impeller shear pins break if an object
comes into the moving parts.
CAUTION:
Use only original equipment
shear pins supplied with the product.
1.
If an impeller shear pin breaks, stop the engine
and wait for the moving parts to stop.
2.
Remove the ON/OFF key and disconnect the
spark plug cable.
3.
Align the hole in the impeller hub (A) with the
holes in the impeller shaft (B) and install a new
¼-20 shear pin (C).
4.
Install a ¼-20 locknut (D) on the shear pin and
tighten.
B
C
A
D
5.
Put the ON/OFF key in the ignition and connect
the spark plug cable to the spark plug.
To replace the fuse
The fuse holders are installed behind the battery
cover.
876 - 011 - 11.05.2020
19