IBM 17351GX User Guide - Page 49

Scanning the switching system, target devices to be scanned, complete one of the following steps

Get IBM 17351GX PDF manuals and user guides View all IBM 17351GX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

Chapter 3: Basic operations 35 4. A message is displayed stating that the mouse and keyboard are reset. 5. Complete one of the following steps: • Click OK to close the message field. • Click X or press Escape to exit without sending a Reset command to the mouse and keyboard. Scanning the switching system In scan mode, the appliance automatically scans from port to port (target device to target device). Use scan mode to monitor the activity of up to 16 target devices, and to specify which target devices to scan and the number of seconds that each target device will be visible. The scanning order is determined by placement of the target device in the list, which is always shown in scanning order. You can choose to list the target devices by name, eID number, or port number by clicking the corresponding button. To add target devices to the scan list, complete the following steps: 1. Click Setup > Scan. The Scan window opens . Figure 3.12: Scan window 2. The window contains a listing of all target devices that are attached to the appliance. To select target devices to be scanned, complete one of the following steps: • Select the check box next to the target devices that you want to scan. • Double-click on a target device name or port. • Press Alt and the eID number of the target device that you want to scan. You can select up to 16 target devices from the list. 3. In the Time field, type the number of seconds (from 3 to 255) of time before the scan moves to the next target device in the sequence. 4. Click OK.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
Chapter 3: Basic operations
35
4.
A message is displayed stating that the mouse and keyboard are reset.
5.
Complete one of the following steps:
•
Click
OK
to close the message field.
•
Click
X
or press Escape to exit without sending a Reset command to the mouse
and keyboard.
Scanning the switching system
In scan mode, the appliance automatically scans from port to port (target device to target device).
Use scan mode to monitor the activity of up to 16 target devices, and to specify which target
devices to scan and the number of seconds that each target device will be visible. The scanning
order is determined by placement of the target device in the list, which is always shown in scanning
order. You can choose to list the target devices by name, eID number, or port number by clicking
the corresponding button.
To add target devices to the scan list, complete the following steps:
1.
Click
Setup > Scan
. The Scan window opens
.
Figure 3.12: Scan window
2.
The window contains a listing of all target devices that are attached to the appliance. To select
target devices to be scanned, complete one of the following steps:
•
Select the check box next to the target devices that you want to scan.
•
Double-click on a target device name or port.
•
Press Alt and the eID number of the target device that you want to scan. You can select up to
16 target devices from the list.
3.
In the
Time
field, type the number of seconds (from 3 to 255) of time before the scan moves to
the next target device in the sequence.
4.
Click
OK
.