IBM 17351GX User Guide - Page 50

Running switching system diagnostics, stop scanning at the currently selected target device.

Get IBM 17351GX PDF manuals and user guides View all IBM 17351GX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

36 Local Console Manager Installation and User's Guide To remove a target device from the scan list, complete the following steps: 1. To select a target device to be removed from the scan list, complete one of the following steps: • In the Scan window, clear the check box next to the target device to be removed. • Double-click on the target device name or port. • Press Shift + Delete to remove the selected target device and all entries below it. • Click the Clear button to remove all target devices from the scan list. 2. Click OK. To start the scan mode, complete the following steps: 1. Click Commands. The Commands window opens. Figure 3.13: Commands window 2. Select Scan Enable in the Commands window. Scanning will be begin immediately. 3. Click X to close the Commands window. To cancel scan mode, complete one of the following steps: • If the OSCAR interface is open, select a target device. • If the OSCAR interface is not open, move the mouse or press any key on the keyboard to stop scanning at the currently selected target device. Running switching system diagnostics You can validate the integrity of the switching system through the Run Diagnostics command. This command checks the main board functional sub-systems (memory, communications, appliance control, and the video channels) for each system controller. When you select the Run Diagnostics button, you will receive a warning that indicates that all users (remote and local) will be disconnected. Click OK to confirm and begin the test.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
36
Local Console Manager Installation and User’s Guide
To remove a target device from the scan list, complete the following steps:
1.
To select a target device to be removed from the scan list, complete one of the following steps:
•
In the Scan window, clear the check box next to the target device to be removed.
•
Double-click on the target device name or port.
•
Press Shift + Delete to remove the selected target device and all entries below it.
•
Click the
Clear
button to remove all target devices from the scan list.
2.
Click
OK
.
To start the scan mode, complete the following steps:
1.
Click
Commands
. The Commands window opens.
Figure 3.13: Commands window
2.
Select
Scan Enable
in the Commands window. Scanning will be begin immediately.
3.
Click
X
to close the Commands window.
To cancel scan mode, complete one of the following steps:
•
If the OSCAR interface is open, select a target device.
•
If the OSCAR interface is not open, move the mouse or press any key on the keyboard to
stop scanning at the currently selected target device.
Running switching system diagnostics
You can validate the integrity of the switching system through the Run Diagnostics command. This
command checks the main board functional sub-systems (memory, communications, appliance
control, and the video channels) for each system controller. When you select the
Run Diagnostics
button, you will receive a warning that indicates that all users (remote and local) will be
disconnected. Click
OK
to confirm and begin the test.