IBM 419452u User Manual - Page 40

Important

Get IBM 419452u - Servers System X3250 M2 Xeon 3.0ghz PDF manuals and user guides
UPC - 883436026604
View all IBM 419452u manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Adapter bracket Adapter Expansion-slot bracket Tab Important: Make sure that the U-shaped opening in the metal adapter bracket engages the tab on the expansion-slot bracket. 10. Follow the cabling instructions, if any, that come with the adapter. 11. Carefully align the riser-card assembly with the guides on the rear of the server and with the riser-card connectors on the system board; then, press down on the assembly. Make sure that the riser-card assembly is fully seated in the riser-card connector on the system board. Power cable PCI-X slot 12. If the riser-card assembly is an optional PCI-X riser-card assembly in the server, reconnect the riser-card power cable to the riser-card assembly. 13. If you are installing a ServeRAID-MR10i controller (2.5-inch drive models only), complete the following steps: a. Disconnect the existing SAS/SATA controller signal cable from the hard disk drive backplane and from the controller; then, remove the cable from the server. b. Route the ServeRAID-MR10i signal cable as shown in the following illustration and connect it to the hard disk drive backplane. 26 IBM System x3250 M2 Types 4190 and 4194: User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Adapter
Adapter
bracket
Expansion-slot
bracket
Tab
Important:
Make
sure
that
the
U-shaped
opening
in
the
metal
adapter
bracket
engages
the
tab
on
the
expansion-slot
bracket.
10.
Follow
the
cabling
instructions,
if
any,
that
come
with
the
adapter.
11.
Carefully
align
the
riser-card
assembly
with
the
guides
on
the
rear
of
the
server
and
with
the
riser-card
connectors
on
the
system
board;
then,
press
down
on
the
assembly.
Make
sure
that
the
riser-card
assembly
is
fully
seated
in
the
riser-card
connector
on
the
system
board.
PCI-X slot
Power cable
12.
If
the
riser-card
assembly
is
an
optional
PCI-X
riser-card
assembly
in
the
server,
reconnect
the
riser-card
power
cable
to
the
riser-card
assembly.
13.
If
you
are
installing
a
ServeRAID-MR10i
controller
(2.5-inch
drive
models
only),
complete
the
following
steps:
a.
Disconnect
the
existing
SAS/SATA
controller
signal
cable
from
the
hard
disk
drive
backplane
and
from
the
controller;
then,
remove
the
cable
from
the
server.
b.
Route
the
ServeRAID-MR10i
signal
cable
as
shown
in
the
following
illustration
and
connect
it
to
the
hard
disk
drive
backplane.
26
IBM
System
x3250
M2
Types
4190
and
4194:
User’s
Guide