IBM 419452u User Manual - Page 64

Using, WebBIOS, Configuration, Utility

Get IBM 419452u - Servers System X3250 M2 Xeon 3.0ghz PDF manuals and user guides
UPC - 883436026604
View all IBM 419452u manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

DIMM 1 Slot DIMM 2 Slot DIMM 3 Slot DIMM 4 Slot SAS/SATA controller card Clear CMOS jumper To clear CMOS and reset the passwords, complete the following steps. Note: All configuration settings will be cleared by this action; you might have to configure the settings again. 1. Review the safety information that begins on page v. 2. Turn off the server and peripheral devices and disconnect all power cords and external cables. 3. Remove the server from the rack and place it on a flat, static-protective surface. 4. Remove the cover. See "Removing the cover" on page 22 for instructions. 5. If necessary, remove the riser-card assembly. See "Installing an adapter" on page 23 for instructions. 6. Move the clear-CMOS jumper from pins 1 and 2 to pins 2 and 3 and leave it there for at least 5 seconds; then, move the clear-CMOS jumper back to pins 1 and 2. 7. Reinstall the riser-card assembly and cover. See "Installing an adapter" on page 23 for instructions. 8. Replace the server in the rack and connect the server to a keyboard, monitor, and mouse; then, connect the server to a power source. 9. Turn on the server. You can now start the Configuration/Setup Utility program and either delete the old password or set a new power-on or administrator password. Using the WebBIOS Configuration Utility Use the WebBIOS Configuration Utility program to configure hot-swap hard disk drives that are connected to the ServeRAID-MR10i controller. To start the WebBIOS Configuration Utility program, complete the following steps: 1. Turn on the server. 50 IBM System x3250 M2 Types 4190 and 4194: User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
DIMM 1 Slot
DIMM 2 Slot
DIMM 3 Slot
DIMM 4 Slot
Clear CMOS jumper
SAS/SATA
controller
card
To
clear
CMOS
and
reset
the
passwords,
complete
the
following
steps.
Note:
All
configuration
settings
will
be
cleared
by
this
action;
you
might
have
to
configure
the
settings
again.
1.
Review
the
safety
information
that
begins
on
page
v.
2.
Turn
off
the
server
and
peripheral
devices
and
disconnect
all
power
cords
and
external
cables.
3.
Remove
the
server
from
the
rack
and
place
it
on
a
flat,
static-protective
surface.
4.
Remove
the
cover.
See
“Removing
the
cover”
on
page
22
for
instructions.
5.
If
necessary,
remove
the
riser-card
assembly.
See
“Installing
an
adapter”
on
page
23
for
instructions.
6.
Move
the
clear-CMOS
jumper
from
pins
1
and
2
to
pins
2
and
3
and
leave
it
there
for
at
least
5
seconds;
then,
move
the
clear-CMOS
jumper
back
to
pins
1
and
2.
7.
Reinstall
the
riser-card
assembly
and
cover.
See
“Installing
an
adapter”
on
page
23
for
instructions.
8.
Replace
the
server
in
the
rack
and
connect
the
server
to
a
keyboard,
monitor,
and
mouse;
then,
connect
the
server
to
a
power
source.
9.
Turn
on
the
server.
You
can
now
start
the
Configuration/Setup
Utility
program
and
either
delete
the
old
password
or
set
a
new
power-on
or
administrator
password.
Using
the
WebBIOS
Configuration
Utility
Use
the
WebBIOS
Configuration
Utility
program
to
configure
hot-swap
hard
disk
drives
that
are
connected
to
the
ServeRAID-MR10i
controller.
To
start
the
WebBIOS
Configuration
Utility
program,
complete
the
following
steps:
1.
Turn
on
the
server.
50
IBM
System
x3250
M2
Types
4190
and
4194:
User’s
Guide