IBM 419452u User Manual - Page 44

Installing, simple-swap, Serial, drive

Get IBM 419452u - Servers System X3250 M2 Xeon 3.0ghz PDF manuals and user guides
UPC - 883436026604
View all IBM 419452u manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Installing a simple-swap Serial ATA hard disk drive Attention: Simple-swap hard disk drives are not hot-swappable. Disconnect all power from the server before you remove or install a simple-swap hard disk drive. To install a simple-swap Serial ATA hard disk drive, complete the following steps. Note: If you have only one hard disk drive, install it in the left drive bay. SATA hard disk drive back plate Hard disk drive assembly Filler panel Attention: To avoid damage to the hard disk drive connectors, make sure that the cover is in place and fully closed whenever you install or remove a hard disk drive. 1. Read the safety information that begins on page v and "Installation guidelines" on page 20. 2. Make sure that the server cover is in place and fully closed. 3. Turn off the server and peripheral devices, and disconnect the power cord and all external cables. 4. Remove the filler panel from the bay. 5. Pull the loops of the drive tray toward each other, and slide the drive into the server until the drive connects to the back plate. 6. Release the loops of the drive tray. 7. Insert the filler panel into the bay to cover the drive. If you have other devices to install, do so now. Otherwise, go to "Completing the installation" on page 38. Note: If a RAID controller or adapter is installed, you might have to reconfigure the disk arrays after you install hard disk drives. See your RAID controller or adapter documentation. To remove a simple-swap SATA drive from the bay, complete the following steps: 1. Read the safety information that begins on page v and "Installation guidelines" on page 20. 2. Turn off the server and peripheral devices, and disconnect the power cord and all external cables. 3. Remove the filler panel from the bay. 30 IBM System x3250 M2 Types 4190 and 4194: User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Installing
a
simple-swap
Serial
ATA
hard
disk
drive
Attention:
Simple-swap
hard
disk
drives
are
not
hot-swappable.
Disconnect
all
power
from
the
server
before
you
remove
or
install
a
simple-swap
hard
disk
drive.
To
install
a
simple-swap
Serial
ATA
hard
disk
drive,
complete
the
following
steps.
Note:
If
you
have
only
one
hard
disk
drive,
install
it
in
the
left
drive
bay.
Filler panel
Hard disk
drive assembly
SATA hard disk
drive back plate
Attention:
To
avoid
damage
to
the
hard
disk
drive
connectors,
make
sure
that
the
cover
is
in
place
and
fully
closed
whenever
you
install
or
remove
a
hard
disk
drive.
1.
Read
the
safety
information
that
begins
on
page
v
and
“Installation
guidelines”
on
page
20.
2.
Make
sure
that
the
server
cover
is
in
place
and
fully
closed.
3.
Turn
off
the
server
and
peripheral
devices,
and
disconnect
the
power
cord
and
all
external
cables.
4.
Remove
the
filler
panel
from
the
bay.
5.
Pull
the
loops
of
the
drive
tray
toward
each
other,
and
slide
the
drive
into
the
server
until
the
drive
connects
to
the
back
plate.
6.
Release
the
loops
of
the
drive
tray.
7.
Insert
the
filler
panel
into
the
bay
to
cover
the
drive.
If
you
have
other
devices
to
install,
do
so
now.
Otherwise,
go
to
“Completing
the
installation”
on
page
38.
Note:
If
a
RAID
controller
or
adapter
is
installed,
you
might
have
to
reconfigure
the
disk
arrays
after
you
install
hard
disk
drives.
See
your
RAID
controller
or
adapter
documentation.
To
remove
a
simple-swap
SATA
drive
from
the
bay,
complete
the
following
steps:
1.
Read
the
safety
information
that
begins
on
page
v
and
“Installation
guidelines”
on
page
20.
2.
Turn
off
the
server
and
peripheral
devices,
and
disconnect
the
power
cord
and
all
external
cables.
3.
Remove
the
filler
panel
from
the
bay.
30
IBM
System
x3250
M2
Types
4190
and
4194:
User’s
Guide