IBM 8482 User Manual - Page 26

POST error messages, Diagnostic programs and error messages, Text messages, Passed, Failed

Get IBM 8482 - eServer xSeries 206 PDF manuals and user guides
UPC - 000435244659
View all IBM 8482 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

POST error messages POST error messages can appear when a problem is detected during startup. For a complete list of POST messages, see "POST error codes" on page 80. Diagnostic programs and error messages The system diagnostic programs are on the IBM Enhanced Diagnostics CD. These programs are the primary method of testing the major components of the server. An IBM Enhanced Diagnostics CD comes with the server. You can also download the latest version of the diagnostic programs from http://www.ibm.com/pc/support/ (see "Downloading the diagnostic program" on page 17). The IBM Enhanced Diagnostic programs isolate problems from the server hardware and software. The programs run independently of the operating system and must be run either from a CD or diskette. Diagnostic error messages indicate that a problem exists; they are not intended to be used to identify a failing part. Troubleshooting and servicing complex problems indicated by error messages should be performed by trained service personnel. Sometimes the first error to occur causes additional errors. In this case, the server displays more than one error message. Always follow the suggested action instructions for the first error message that appears. Error codes that might be displayed are listed at "Diagnostic error codes" on page 83. Text messages The diagnostic text message format is as follows: result test_specific_string where: result is one of the following results: Passed This test was completed without any errors. Failed This test discovered an error. User Aborted You stopped the test before it was completed. Not Applicable You attempted to test a device that is not present in the server. Aborted The test could not proceed because of the server configuration. Warning A possible problem was reported during the test (for example, a device that was to be tested is not installed). test_specific_string is an error code or other information about the error. 16 xSeries 206 Type 8482 and 8487: Hardware Maintenance Manual and Troubleshooting Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
POST error messages
POST error messages can appear when a problem is detected during startup. For a
complete list of POST messages, see “POST error codes” on page 80.
Diagnostic programs and error messages
The system diagnostic programs are on the
IBM Enhanced Diagnostics
CD. These
programs are the primary method of testing the major components of the server.
An
IBM Enhanced Diagnostics
CD comes with the server. You can also download
the latest version of the diagnostic programs from http://www.ibm.com/pc/support/
(see “Downloading the diagnostic program” on page 17).
The IBM Enhanced Diagnostic programs isolate problems from the server hardware
and software. The programs run independently of the operating system and
must
be run either from a CD or diskette
.
Diagnostic error messages indicate that a problem exists; they are not intended to
be used to identify a failing part. Troubleshooting and servicing complex problems
indicated by error messages should be performed by trained service personnel.
Sometimes the first error to occur causes additional errors. In this case, the server
displays more than one error message. Always follow the suggested action
instructions for the
first
error message that appears.
Error codes that might be displayed are listed at “Diagnostic error codes” on page
83.
Text messages
The diagnostic text message format is as follows:
result test_specific_string
where:
result
is one of the following results:
Passed
This test was completed without any errors.
Failed
This test discovered an error.
User Aborted
You stopped the test before it was completed.
Not Applicable
You attempted to test a device that is not present in the server.
Aborted
The test could not proceed because of the server configuration.
Warning
A possible problem was reported during the test (for example, a
device that was to be tested is not installed).
test_specific_string
is an error code or other information about the error.
16
xSeries 206 Type 8482 and 8487: Hardware Maintenance Manual and Troubleshooting Guide