IBM 8649 Hardware Maintenance Manual - Page 13

Features and specifications The following table provides a summary of the features and specifications of your server. Depending on your server model, some features might not be available, or some specifications might not apply. You can use the Configuration/Setup Utility program in your server to determine the specific type of microprocessor that is on the system board. Table 1. Features and specifications Microprocessor: v Intel® Xeon Processor v 512 KB Level-2 cache v 400 MHz or 533 MHz front-side bus (FSB) v Support for up to two microprocessors Memory: v Minimum: 256 MB v Maximum: 8 GB v Type: PC2100, double-data-rate (DDR) v Connectors: four dual inline memory module (DIMM) connectors, two-way interleaved Drives standard: v Diskette: 1.44 MB (two mode) v CD-ROM: IDE Expansion bays: v Six open hot-swap, slim-high, 3.5-inch drive bays (some models) v Four slim-high, 3.5-inch drive bays with one hard disk drive installed (some models) v Two 5.25-inch bays (CD-ROM drive installed in one bay) v One 3.5-inch removable-media drive bay (diskette drive installed) PCI expansion slots: v Four PCI-X 100 MHz/64-bit v One PCI 33 MHz/32-bit Cooling: Three speed-controlled fans Integrated functions: v Support for IBM Remote Supervisor Adapter v Broadcom 5703 10/100/1000 Ethernet controller on the system board with RJ-45 Ethernet port v Two serial ports v One parallel port v Integrated SCSI controller with RAID capabilities and two Ultra320 SCSI ports (one internal, one optional external) v Four Universal Serial Bus (USB) v2.0 ports (two on front and two on rear of enclosure) v Keyboard port v Mouse port v Audio ports (rear) - Line out - Mic - Line in v ATA-100 dual-channel IDE controller v ATI Rage XL video (mini-PCI) - Compatible with SVGA and VGA - 8 MB video memory Electrical input: v Sine-wave input (50 or 60 Hz) required v Input voltage and frequency ranges automatically selected v Input voltage low range: - Minimum: 100 V ac - Maximum: 127 V ac v Input voltage high range: - Minimum: 200 V ac - Maximum: 240 V ac v Input kilovolt-amperes (kVA) approximately: - Minimum: 0.15 kVA (all models) - Maximum: 0.80 kVA with standard power supply, 0.62 kVA with optional redundant hot-swap power supplies Heat output: Approximate heat output in British thermal units (Btu) per hour v Minimum configuration: 341 Btu/hour (100 watts) v Maximum configuration: 2455 Btu/hour (720 watts) with standard power supply, 1910 Btu/hour (560 watts) with optional redundant hot-swap power supplies Error LEDs: v Fans v Memory v Microprocessors Environment: v Air temperature: - Server on: 10° to 35°C (50° to 95°F) Altitude: 0 to 2134 m (7000 ft) - Server off: -40° to +60°C (-40° to 140°F) Power supplies: Maximum altitude: 2134 m (7000 ft) v Hot-swap (some models) v Humidity (operating and storage): 8% to Standard: Two 350 watt output (115-230 80% V ac) for redundancy v Non-hot-swap (some models) Acoustical noise emissions: Standard: One 425 watt output (115-230 v Sound power, idle: 5.3 bel maximum V ac) v Sound power, operating: 5.6 bel maximum Upgradeable microcode: BIOS upgrades (when available) can update EEPROMs on the system board Size: v Height: 440 mm (18.4 in.) v Depth: 660 mm (26 in.) v Width: 217 mm (6.5 in.) v Weight: 20 kg (44 lb) to 25.8 kg (57 lb) depending upon configuration Chapter 1. Introducing the IBM xSeries 225 Type 8649 server 3