IBM 8649 Hardware Maintenance Manual - Page 89

Hot-swap, drive

Get IBM 8649 - Eserver xSeries 225 PDF manuals and user guides
UPC - 000435133427
View all IBM 8649 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 89 highlights

Hot-swap hard disk drive cage Before you begin: v Read "Safety information" on page 129 v Review the information in "System reliability considerations" on page 33 To remove the hot-swap hard disk drive cage, complete the following steps: 1. Turn off the server, if it is on. 2. Unplug the server, and disconnect all external cables. 3. Remove the front bezel. See "Removing the bezel" on page 37 4. Remove the side cover. See "Removing the side cover" on page 36 5. Remove the frame-support bracket. See "Removing and installing the support bracket" on page 38 6. Remove any hard disk drives or drive fillers from the drives. 7. Disconnect the hard disk drive cables that connect to the system board. 8. Remove the screw from the front of the hard disk drive cage. 9. Move the cage slightly in and up until it is free of the chassis and lift it out of the server. To replace the hard disk drive cage, reverse the steps. Chapter 5. Field replaceable units 79

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
Hot-swap
hard
disk
drive
cage
Before
you
begin:
v
Read
“Safety
information”
on
page
129
v
Review
the
information
in
“System
reliability
considerations”
on
page
33
To
remove
the
hot-swap
hard
disk
drive
cage,
complete
the
following
steps:
1.
Turn
off
the
server,
if
it
is
on.
2.
Unplug
the
server,
and
disconnect
all
external
cables.
3.
Remove
the
front
bezel.
See
“Removing
the
bezel”
on
page
37
4.
Remove
the
side
cover.
See
“Removing
the
side
cover”
on
page
36
5.
Remove
the
frame-support
bracket.
See
“Removing
and
installing
the
support
bracket”
on
page
38
6.
Remove
any
hard
disk
drives
or
drive
fillers
from
the
drives.
7.
Disconnect
the
hard
disk
drive
cables
that
connect
to
the
system
board.
8.
Remove
the
screw
from
the
front
of
the
hard
disk
drive
cage.
9.
Move
the
cage
slightly
in
and
up
until
it
is
free
of
the
chassis
and
lift
it
out
of
the
server.
To
replace
the
hard
disk
drive
cage,
reverse
the
steps.
Chapter
5.
Field
replaceable
units
79