IBM 8676 Hardware Maintenance Manual - Page 54

Removing, cover, bezel

Get IBM 8676 - Eserver xSeries 335 PDF manuals and user guides
UPC - 087944770107
View all IBM 8676 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

Removing the cover and bezel Complete the following steps to remove the server cover and bezel: 1. Read "Safety information" on page 119 and "Installation guidelines" on page 37. 2. Turn off the server and all attached peripheral devices. Disconnect all power cords; then, disconnect all external signal cables from the server. 3. Remove the server from the rack. 4. Lift the cover release latch. The cover slides to the rear approximately 13 mm (0.5 inch). Captive screws Bezel retention tabs USB option tray Bezel retention tabs Retention clip 5. Slide the cover back, and lift the cover off the server. Attention: To ensure adequate cooling and airflow, replace the cover before turning on the server. Do not operate the server with the cover removed. 6. Press in on the USB option tray (below hard disk drive bay 1) to release it and slide the tray out until it stops; then, press the retention clip at the bottom rear of the tray and remove the tray from the server. Note: You only need to remove the USB option tray and the bezel if you are installing a non-hot-swap hard disk drive. It is not necessary if you are installing other options in the server. 7. Press on the bezel retention tabs on the top, right side and bottom of the server, and pull the bezel directly away from the server. To reinstall the cover and bezel, see "Installing the cover and bezel" on page 59. 44 xSeries 335 Type 8676, Type 8830: Hardware Maintenance Manual and Troubleshooting Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
Removing
the
cover
and
bezel
Complete
the
following
steps
to
remove
the
server
cover
and
bezel:
1.
Read
“Safety
information”
on
page
119
and
“Installation
guidelines”
on
page
37.
2.
Turn
off
the
server
and
all
attached
peripheral
devices.
Disconnect
all
power
cords;
then,
disconnect
all
external
signal
cables
from
the
server.
3.
Remove
the
server
from
the
rack.
4.
Lift
the
cover
release
latch.
The
cover
slides
to
the
rear
approximately
13
mm
(0.5
inch).
Bezel retention
tabs
Bezel
retention
tabs
USB option tray
Captive screws
Retention
clip
5.
Slide
the
cover
back,
and
lift
the
cover
off
the
server.
Attention:
To
ensure
adequate
cooling
and
airflow,
replace
the
cover
before
turning
on
the
server.
Do
not
operate
the
server
with
the
cover
removed.
6.
Press
in
on
the
USB
option
tray
(below
hard
disk
drive
bay
1)
to
release
it
and
slide
the
tray
out
until
it
stops;
then,
press
the
retention
clip
at
the
bottom
rear
of
the
tray
and
remove
the
tray
from
the
server.
Note:
You
only
need
to
remove
the
USB
option
tray
and
the
bezel
if
you
are
installing
a
non-hot-swap
hard
disk
drive.
It
is
not
necessary
if
you
are
installing
other
options
in
the
server.
7.
Press
on
the
bezel
retention
tabs
on
the
top,
right
side
and
bottom
of
the
server,
and
pull
the
bezel
directly
away
from
the
server.
To
reinstall
the
cover
and
bezel,
see
“Installing
the
cover
and
bezel”
on
page
59.
44
xSeries
335
Type
8676,
Type
8830:
Hardware
Maintenance
Manual
and
Troubleshooting
Guide