IBM 8837 User Manual - Page 26

Installing, simple, drive, additional, microprocessor - way

Get IBM 8837 - eServer xSeries 336 PDF manuals and user guides
UPC - 000435421401
View all IBM 8837 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Complete the following steps to install a 3.5-inch hot-swap SCSI hard disk drive: 1. Read the safety information. 2. Remove the filler panel from the appropriate drive bay. Note: To make sure there is adequate system cooling, do not operate the server for more than 2 minutes without either a hard disk drive or a filler panel installed in each bay. 3. Place the drive handle in the open position and slide the drive into the bay. 4. Close the drive handle. 5. If you have other options to install or remove, do so now. 6. Go to "Completing the installation" on page 22. Installing a simple swap hard disk drive Before you install a simple swap SATA hard disk drive, turn off the server and all attached peripheral devices. Disconnect all power cords; then, disconnect all external signal cables from the server. This section provides an overview of the procedure for installing a simple swap SATA hard disk drive. For detailed instructions, see the Option Installation Guide. Drive-tray assembly Drive handle Filler panel Complete the following steps to install a simple swap SATA hard disk drive: 1. Read the safety information. 2. Remove the filler panel for the drive from either bay. Note: To make sure there is adequate system cooling, do not operate the server for more than 2 minutes without either a hard disk drive or a filler panel installed in each bay. 3. Slide the drive into the rear of the bay until it snaps into place with the rear panel mount connector. 4. Install the filler panel for the drive. 5. If you have other options to install, install them now. Otherwise, go to "Completing the installation" on page 22. Installing an additional microprocessor The following notes describe the type of microprocessor that the server supports and other information that you must consider when installing a microprocessor: v The server supports up to two microprocessors (two-way support); the IBM xSeries 336 server comes with one Xeon microprocessor installed. With two microprocessors, the server can operate as a symmetric multiprocessing (SMP) server. 14 IBM xSeries 336 Type 8837: Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
Complete
the
following
steps
to
install
a
3.5-inch
hot-swap
SCSI
hard
disk
drive:
1.
Read
the
safety
information.
2.
Remove
the
filler
panel
from
the
appropriate
drive
bay.
Note:
To
make
sure
there
is
adequate
system
cooling,
do
not
operate
the
server
for
more
than
2
minutes
without
either
a
hard
disk
drive
or
a
filler
panel
installed
in
each
bay.
3.
Place
the
drive
handle
in
the
open
position
and
slide
the
drive
into
the
bay.
4.
Close
the
drive
handle.
5.
If
you
have
other
options
to
install
or
remove,
do
so
now.
6.
Go
to
“Completing
the
installation”
on
page
22.
Installing
a
simple
swap
hard
disk
drive
Before
you
install
a
simple
swap
SATA
hard
disk
drive,
turn
off
the
server
and
all
attached
peripheral
devices.
Disconnect
all
power
cords;
then,
disconnect
all
external
signal
cables
from
the
server.
This
section
provides
an
overview
of
the
procedure
for
installing
a
simple
swap
SATA
hard
disk
drive.
For
detailed
instructions,
see
the
Option
Installation
Guide
.
Drive-tray
assembly
Drive handle
Filler panel
Complete
the
following
steps
to
install
a
simple
swap
SATA
hard
disk
drive:
1.
Read
the
safety
information.
2.
Remove
the
filler
panel
for
the
drive
from
either
bay.
Note:
To
make
sure
there
is
adequate
system
cooling,
do
not
operate
the
server
for
more
than
2
minutes
without
either
a
hard
disk
drive
or
a
filler
panel
installed
in
each
bay.
3.
Slide
the
drive
into
the
rear
of
the
bay
until
it
snaps
into
place
with
the
rear
panel
mount
connector.
4.
Install
the
filler
panel
for
the
drive.
5.
If
you
have
other
options
to
install,
install
them
now.
Otherwise,
go
to
“Completing
the
installation”
on
page
22.
Installing
an
additional
microprocessor
The
following
notes
describe
the
type
of
microprocessor
that
the
server
supports
and
other
information
that
you
must
consider
when
installing
a
microprocessor:
v
The
server
supports
up
to
two
microprocessors
(two-way
support);
the
IBM
xSeries
336
server
comes
with
one
Xeon
microprocessor
installed.
With
two
microprocessors,
the
server
can
operate
as
a
symmetric
multiprocessing
(SMP)
server.
14
IBM
xSeries
336
Type
8837:
Installation
Guide