IBM HS40 Setup Guide - Page 11

Starting the BladeCenter management-module Web interface, Password: PASSW0RD note the zero, not O - firmware

Get IBM HS40 - BladeCenter - 8839 PDF manuals and user guides
UPC - 000435160188
View all IBM HS40 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Starting the BladeCenter management-module Web interface Note: The sample screens that appear in this document might differ slightly from the screens displayed by your system. Screen content varies based on the type of BladeCenter unit that you are using and the firmware versions and options that are installed. The management-module Web interface is used to perform SOL configuration. The management-module Web interface supports only configuration and monitoring of the command-line interface and SOL and cannot be used to start command-line interface or SOL sessions. Complete the following steps to start the BladeCenter management-module Web interface: 1. Open a Web browser. In the address or URL field, type the IP address or host name that is assigned for the management-module remote connection. The Enter Network Password window opens. 2. Type your user name and password. If you are logging in to the management module for the first time, you can obtain your user name and password from your system administrator. All login attempts are documented in the event log. The initial user ID and password for the management module are: v User ID: USERID (all capital letters) v Password: PASSW0RD (note the zero, not O, in PASSW0RD) 3. Follow the instructions on the screen. Be sure to set the timeout value that you want for your Web session. The BladeCenter management-module Web interface window opens. Chapter 1. Introduction 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
Starting the BladeCenter management-module Web interface
Note:
The sample screens that appear in this document might differ slightly from
the screens displayed by your system. Screen content varies based on the type of
BladeCenter unit that you are using and the firmware versions and options that
are installed.
The management-module Web interface is used to perform SOL configuration. The
management-module Web interface supports only configuration and monitoring of
the command-line interface and SOL and cannot be used to start command-line
interface or SOL sessions.
Complete the following steps to start the BladeCenter management-module Web
interface:
1.
Open a Web browser. In the address or URLfield, type the IP address or host
name that is assigned for the management-module remote connection.
The Enter Network Password window opens.
2.
Type your user name and password. If you are logging in to the management
module for the first time, you can obtain your user name and password from
your system administrator. All login attempts are documented in the event log.
The initial user ID and password for the management module are:
v
User ID: USERID (all capital letters)
v
Password: PASSW0RD (note the zero, not O, in PASSW0RD)
3.
Follow the instructions on the screen. Be sure to set the timeout value that you
want for your Web session.
The BladeCenter management-module Web interface window opens.
Chapter 1. Introduction
5