IBM HS40 Setup Guide - Page 17

Installing and configuring SSH for SOL, SSH Server Key Management

Get IBM HS40 - BladeCenter - 8839 PDF manuals and user guides
UPC - 000435160188
View all IBM HS40 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

1) In the navigation pane, click I/O Module Tasks → Configuration. 2) Scroll to the Bay 1 (Ethernet SM)* section. 3) Set the values in the New Static IP Configuration fields, if they are not already correct as listed in the Current IP Configuration section. The values must be in the following formats: v IP address: x.x.x.x v Subnet mask: x.x.x.x v Gateway address: x.x.x.x The static IP configuration values specify valid IP addresses of the form x.x.x.x, where each x is a number from 0 to 255. 4) If you changed any values, click Save. 5. Complete the following steps to restart the management module. Restarting the management module ends the current BladeCenter management-module Web interface session. a. In the navigation pane, click MM Control → Restart MM. b. Click Restart. c. Click OK to confirm. d. Click Yes to restart the management module and end the session. Installing and configuring SSH for SOL Complete the following steps to install and configure Secure Shell Server (SSH) for SOL: 1. Start the BladeCenter management-module Web interface (see "Starting the BladeCenter management-module Web interface" on page 5). 2. If you have not previously installed a security key file, complete the following steps. Otherwise, go to step 3. a. In the navigation pane, click MM Control → Security. b. Download the latest version of the SSH security key file from http://www.ibm.com/support/. Navigate to the Install SSL/SSH section and click BladeCenter firmware update. c. Click Browse and select the file that was downloaded in step 2b. d. Click Install SSL/SSH. e. Scroll to the Install SSL/SSH section and click Configure and enable. 3. Complete the following steps to generate the SSH Server Private Key: a. In the navigation pane, click MM Control → Security. b. Scroll to the SSH Server Key Management section and click Generate SSH Server Private Key. c. Click OK to confirm. 4. Complete the following steps to enable SSH: a. Scroll to the Secure Shell (SSH) Server section. b. Select Enabled for the SSH Server option; then, click Save. c. Click OK to confirm. 5. Complete the following steps to restart the management module. Restarting the management module ends the current BladeCenter management-module Web interface session. a. In the navigation pane, click MM Control → Restart MM. b. Click Restart. Chapter 2. General configuration 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
1)
In the navigation pane, click
I/O Module Tasks
→
Configuration
.
2)
Scroll to the
Bay 1 (Ethernet SM)*
section.
3)
Set the values in the
New Static IP Configuration
fields, if they are not
already correct as listed in the
Current IP Configuration
section. The
values must be in the following formats:
v
IP address:
x.x.x.x
v
Subnet mask:
x.x.x.x
v
Gateway address:
x.x.x.x
The static IP configuration values specify valid IP addresses of the form
x.x.x.x
, where each
x
is a number from 0 to 255.
4)
If you changed any values, click
Save
.
5.
Complete the following steps to restart the management module. Restarting the
management module ends the current BladeCenter management-module Web
interface session.
a.
In the navigation pane, click
MM Control
→
Restart MM
.
b.
Click
Restart
.
c.
Click
OK
to confirm.
d.
Click
Yes
to restart the management module and end the session.
Installing and configuring SSH for SOL
Complete the following steps to install and configure Secure Shell Server (SSH) for
SOL:
1.
Start the BladeCenter management-module Web interface (see “Starting the
BladeCenter management-module Web interface” on page 5).
2.
If you have not previously installed a security key file, complete the following
steps. Otherwise, go to step 3.
a.
In the navigation pane, click
MM Control
→
Security
.
b.
Download the latest version of the SSH security key file from
Install SSL/SSH
section
and click
BladeCenter firmware update
.
c.
Click
Browse
and select the file that was downloaded in step 2b.
d.
Click
Install SSL/SSH
.
e.
Scroll to the
Install SSL/SSH
section and click
Configure and enable
.
3.
Complete the following steps to generate the SSH Server Private Key:
a.
In the navigation pane, click
MM Control
→
Security
.
b.
Scroll to the
SSH Server Key Management
section and click
Generate SSH
Server Private Key
.
c.
Click
OK
to confirm.
4.
Complete the following steps to enable SSH:
a.
Scroll to the
Secure Shell (SSH) Server
section.
b.
Select
Enabled
for the
SSH Server
option; then, click
Save
.
c.
Click
OK
to confirm.
5.
Complete the following steps to restart the management module. Restarting the
management module ends the current BladeCenter management-module Web
interface session.
a.
In the navigation pane, click
MM Control
→
Restart MM
.
b.
Click
Restart
.
Chapter 2. General configuration
11