IBM HS40 Setup Guide - Page 39

Configuring the Nortel Networks Layer 2-7 GbE Switch Module for IBM BladeCenter

Get IBM HS40 - BladeCenter - 8839 PDF manuals and user guides
UPC - 000435160188
View all IBM HS40 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

in the same subnet, you must modify them before you continue. See "Configuring the management module" on page 9 for information. 5. Scroll to the Bay 1 (Ethernet SM)* section; then, click Advanced Management. 6. Scroll to the Start Telnet/Web Session section; then, click Start Web Session. This will start a new Web browser session and connect to the IBM 4-Port Gb Ethernet Switch Module for BladeCenter Web interface. 7. Log in to the IBM 4-Port Gb Ethernet Switch Module for BladeCenter Web interface. 8. Click Maintenance. 9. Click Using Browser. 10. Click Upgrade Firmware/Configuration. 11. Click Browse; then, select the firmware update file that you obtained in step 1. 12. Click Start; then, click Yes to confirm each time you are asked a question. 13. Close the Web browser. 14. Complete the following steps to restart the I/O module: a. In the navigation pane, click I/O Module Tasks → Admin/Power/Restart. b. Select your IBM 4-Port Gb Ethernet Switch Module for BladeCenter and click Restart Module(s) and Run Standard Diagnostics. c. Click OK to confirm. Configuring the Nortel Networks Layer 2-7 GbE Switch Module for IBM BladeCenter Complete the following steps to update the firmware of the Nortel Networks Layer 2-7 GbE Switch Module for IBM BladeCenter. No configuration is required for the Nortel Networks Layer 2-7 GbE Switch Module for IBM BladeCenter to enable SOL. Notes: v You will not be able to perform this procedure if the values for the network configuration of the Nortel Networks Layer 2-7 GbE Switch Module for IBM BladeCenter are not within the same subnet as the BladeCenter management-module network interfaces (eth0 and eth1). See "Configuring the management module" on page 9 for information. v These steps require that an accessible TFTP (Trivial FTP) server is present on your production network. 1. Obtain the latest version of Nortel Networks Layer 2-7 GbE Switch Module for IBM BladeCenter firmware from http://www.ibm.com/support/. 2. Update the Nortel Networks Layer 2-7 GbE Switch Module for IBM BladeCenter firmware, following the instructions that come with the update file that you downloaded. The Nortel Networks Layer 2-7 GbE Switch Module has multiple firmware images. These images must all be updated, in the correct order. Make sure that you restart the Nortel Networks Layer 2-7 GbE Switch Module after updating each firmware image. Chapter 4. Special component requirements 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
in the same subnet, you must modify them before you continue. See
“Configuring the management module” on page 9 for information.
5.
Scroll to the
Bay 1 (Ethernet SM)*
section; then, click
Advanced
Management
.
6.
Scroll to the
Start Telnet/Web Session
section; then, click
Start Web Session
.
This will start a new Web browser session and connect to the IBM 4-Port Gb
Ethernet Switch Module for BladeCenter Web interface.
7.
Log in to the IBM 4-Port Gb Ethernet Switch Module for BladeCenter Web
interface.
8.
Click
Maintenance
.
9.
Click
Using Browser
.
10.
Click
Upgrade Firmware/Configuration
.
11.
Click
Browse
; then, select the firmware update file that you obtained in step 1.
12.
Click
Start
; then, click
Yes
to confirm each time you are asked a question.
13.
Close the Web browser.
14.
Complete the following steps to restart the I/O module:
a.
In the navigation pane, click
I/O Module Tasks
→
Admin/Power/Restart
.
b.
Select your IBM 4-Port Gb Ethernet Switch Module for BladeCenter and
click
Restart Module(s) and Run Standard Diagnostics
.
c.
Click
OK
to confirm.
Configuring the Nortel Networks Layer 2-7 GbE Switch Module for IBM
BladeCenter
Complete the following steps to update the firmware of the Nortel Networks Layer
2-7 GbE Switch Module for IBM BladeCenter. No configuration is required for the
Nortel Networks Layer 2-7 GbE Switch Module for IBM BladeCenter to enable
SOL.
Notes:
v
You will not be able to perform this procedure if the values for the network
configuration of the Nortel Networks Layer 2-7 GbE Switch Module for IBM
BladeCenter are not within the same subnet as the BladeCenter
management-module network interfaces (eth0 and eth1). See “Configuring the
management module” on page 9 for information.
v
These steps require that an accessible TFTP (Trivial FTP) server is present on
your production network.
1.
Obtain the latest version of Nortel Networks Layer 2-7 GbE Switch Module for
IBM BladeCenter firmware from http://www.ibm.com/support/.
2.
Update the Nortel Networks Layer 2-7 GbE Switch Module for IBM
BladeCenter firmware, following the instructions that come with the update file
that you downloaded. The Nortel Networks Layer 2-7 GbE Switch Module has
multiple firmware images. These images must all be updated, in the correct
order. Make sure that you restart the Nortel Networks Layer 2-7 GbE Switch
Module after updating each firmware image.
Chapter 4. Special component requirements
33