IBM HS40 Setup Guide - Page 32

Devices and I/O Ports, Legacy Option ROM Display

Get IBM HS40 - BladeCenter - 8839 PDF manuals and user guides
UPC - 000435160188
View all IBM HS40 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

5. When the prompt Press Setup is displayed, press F1. If you have set an administrator password, you must type the administrator password to access the full Setup-utility menu. If you do not type the administrator password, a limited Setup-utility menu is available. 6. Select System Settings and then press Enter. 7. Select Devices and I/O Ports and then press Enter. 8. Select Console Redirection Settings and then press Enter. 9. From the Console Redirection Settings menu: a. If you are using a serial breakout cable with a BladeCenter H unit or a BladeCenter S unit, set COM Port 1 to Enable; otherwise, set it to Disable. b. Set COM Port 2 to Enable. c. Set Remote Console to Enable. d. Set Legacy Option ROM Display to COM Port 2. e. Set the following COM2 Settings: 1) Make sure that the Baud Rate is set to 115200. Note: The settings for Data Bits, Parity, and Stop Bits are static and cannot be changed. 2) Set Terminal Emulation to ANSI (default) or VT100, depending on your system configuration. 3) Set Active After Boot to Enable. 4) Set Flow Control to Hardware. 26 BladeCenter: Serial over LAN Setup Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
5.
When the prompt
Press <F1> Setup
is displayed, press F1. If you have set an
administrator password, you must type the administrator password to access
the full Setup-utility menu. If you do not type the administrator password, a
limited Setup-utility menu is available.
6.
Select
System Settings
and then press Enter.
7.
Select
Devices and I/O Ports
and then press Enter.
8.
Select
Console Redirection Settings
and then press Enter.
9.
From the Console Redirection Settings menu:
a.
If you are using a serial breakout cable with a BladeCenter H unit or a
BladeCenter S unit, set
COM Port 1
to
Enable
; otherwise, set it to
Disable
.
b.
Set
COM Port 2
to
Enable
.
c.
Set
Remote Console
to
Enable
.
d.
Set
Legacy Option ROM Display
to
COM Port 2
.
e.
Set the following
COM2 Settings
:
1)
Make sure that the
Baud Rate
is set to
115200
.
Note:
The settings for
Data Bits
,
Parity
, and
Stop Bits
are static and
cannot be changed.
2)
Set
Terminal Emulation
to
ANSI
(default) or
VT100
, depending on
your system configuration.
3)
Set
Active After Boot
to
Enable
.
4)
Set
Flow Control
to
Hardware
.
26
BladeCenter: Serial over LAN Setup Guide