Icom IC-V10MR Operating Guide - Page 23
User setting operation, Turning the Beep function ON or OFF, Setting the Beep level
View all Icom IC-V10MR manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 23 highlights
4 USER SET MODE User setting operation The user can set the Beep function, Beep level, the Ringer level, the squelch level, the microphone gain, the VOX function, and the VOX gain with a key operation and hearing beeps. DDTurning the Beep function ON or OFF NOTE: Turn ON the Beep function when you set the Beep level, the Ringer level, the microphone gain, the VOX function, the VOX gain, and the squelch level. 1. Rotate [VOL] to turn OFF the transceiver. 2. Set [Rotary Selector] to any channel other than Channel 16. 3. While holding down [Lower], rotate [VOL] to turn ON the transceiver. •• The transceiver enters the Beep level set mode. 4. Push [Lower] to turn the Beep function ON or OFF. LLIf a beep sounds after pushing [Lower], the Beep function is ON. If no beep sounds after pushing [Lower], the Beep function is OFF. LLThe transceiver saves the setting every time you change it. LLIf desired, push [Upper] to adjust the Beep level. 5. Rotate [VOL] to turn OFF the transceiver, then turn it ON again to restart the normal operation. DDSetting the Beep level NOTE: The Beep function should be ON. 1. Rotate [VOL] to turn OFF the transceiver. 2. Set [Rotary Selector] to any channel other than Channel 16. 3. While holding down [Lower], rotate [VOL] to turn ON the transceiver. •• An opening beep sounds, and the selected channel number will be announced. LLThe transceiver can announce the number only when the selected channel is programmed. •• The transceiver enters the Beep level set mode. 4. Push [Upper] to change the Beep level. •• Beep at the set level sounds every time you push [Upper]. LLRepeatedly pushing [Upper] changes the Beep level, as shown below. 1 2 5 5 (Linked) 2 (Linked) 1 (Linked) LLThe settable range: 1 to 5 and 1 (Linked) to 5 (Linked). When setting the Linked option, the Beep level is adjustable with [VOL]. 5. Rotate [VOL] to turn OFF the transceiver, then turn it ON again to restart the normal operation. DDSetting the Ringer level NOTE: The Beep function should be ON. 1. Rotate [VOL] to turn OFF the transceiver. 2. Set [Rotary Selector] to Channel 16. 3. While holding down [Lower], rotate [VOL] to turn ON the transceiver. •• An opening beep sounds and the selected channel number will be announced. LLThe transceiver can announce the number only when the selected channel is programmed. •• The transceiver enters the Ringer Level set mode. 4. Push [Upper] to increase, or push [Lower] to decrease the Ringer level. •• Beep at the set level sounds every time you push [Upper] or [Lower]. LLRepeatedly pushing [Upper] or [Lower] changes the Ringer level, as shown below. 1 2 5 5 (Linked) 2 (Linked) 1 (Linked) LLThe settable range is 1 to 5 or 1 (Linked) to 5 (Linked). When setting the Linked option, the Ringer level is adjustable with [VOL]. 5. Rotate [VOL] to turn OFF the transceiver, then turn it ON again to restart the normal operation. DDSetting the squelch level The squelch circuit mutes the received audio signal, depending on the signal strength. NOTE: The Beep function should be ON. 1. Rotate [VOL] to turn OFF the transceiver. 2. Set [Rotary Selector] to any channel other than Channel 16. 3. While holding down [Upper], rotate [VOL] to turn ON and enter the squelch level adjustment mode. 4. Push [Upper] to increase the squelch level or push [Lower] to decrease the squelch level. LLThe settable range is between 0 (open) to 9 (tight). •• A beep sounds after pushing [Upper] or [Lower]. An error beep sounds when the settable range is exceeded. 5. Rotate [VOL] to turn OFF the transceiver, then turn it ON again to restart the normal operation. 4-5