Insignia NSHT511 User Manual (English) - Page 20

Insignia NS-HT511 Home Theater System Use the remote control within about 16 feet (5 meters) of the receiver and within 30 degrees of perpendicular to the front of the receiver. Cautions • Do not expose the remote control to shock. In addition, do not expose the remote control to liquids, and do not place in an area with high humidity. • Do not place the remote control under direct sunlight. The heat may cause deformation of the remote control. • The remote control may not work properly if the remote sensor window of the receiver is under direct sunlight or strong lighting. In such a case, change the angle of the lighting or receiver, or operate the remote control closer to the remote sensor window. Configuring speakers (Sp Config menu) This section explains how to specify which speakers are connected and defines their sizes. For speakers with a cone diameter larger than 6.5 inches (16 cm), specify Large (full band). For those with a smaller diameter, specify Small (default crossover 120 Hz). The crossover frequency can be changed in the Crossover submenu. See "Using on-screen setup menus" on page 22 for information on accessing and using the menus. Note Speaker Configuration, Crossover Frequency, and Double Bass settings are disabled while headphones are connected, or when Audio TV OUT is set to On. Speaker(s) Subwoofer Front Center and Surround Configuration Yes-if a subwoofer is connected. No-If no subwoofer is connected. Small-If speaker cone is 6.5 inches (16 cm) or less in diameter. Large-If speaker cone is larger than 6.5 inches (16 cm) in diameter. Note: If the Subwoofer setting is No, the default setting for this is Large and cannot be changed. Small-If speaker cone is 6.5 inches (16 cm) or less in diameter. Large-If speaker cone is larger than 6.5 inches (16 cm) in diameter. None-If no center speaker is connected. Note: If the Front setting is Small, the Large option cannot be selected. Setting the crossover frequency (Crossover Frequency submenu of Sp Config menu) This setting is recommended for the speakers that you specify as Small. To get the best bass performance from your speaker system, you need to set the crossover frequency according to the size and frequency response of your speakers. Options include 40Hz, 50Hz, 60Hz, 70Hz, 80Hz, 90Hz, 100Hz, 120Hz, 150Hz, and 200Hz. Use the diameter of the smallest speaker in your system when choosing the crossover frequency. See "Using on-screen setup menus" on page 22 for information on accessing and using the menus. Speaker cone diameter Recommended Crossover Frequency Over 8 in. (20 cm) 40/50/60 Hz 6-1/2 to 8 in. (16 to 20 cm) 70 Hz, 80 Hz, 90 Hz 5-1/4 to 6-1/2 in. (13 to 16 cm) 100 Hz 3-1/2 to 5-1/4 in. (9 to 13 cm) 120 Hz Under 3-1/2 in. (9 cm) 150/200 Hz Notes • • For a more accurate setting, look up your speaker's specifications. Choose a higher crossover frequency if you want more sound from your subwoofer. Using the Double Bass setting (Double Bass submenu of Sp Config menu) Lets you boost bass output by feeding bass sounds from the front left, right, and center channels to the subwoofer. Optional settings are On and Off. Note This function can only be set if the Subwoofer setting is Yes, and the Front setting is Large. Setting wireless (This setting appears only when RF-RBCARD is inserted) This menu is used if you are connecting your home theater front left/right, surround, or subwoofer channels using Rocketboost wireless (see "Rocketboost Setup" on page 12 for more details about Rocketboost). The On menu option results in the wired and wireless channels in your home theater to be synchronized in time. If any of these channels in your home theater are connected with Rocketboost wireless, then set those channels to On. For example, if you are using Rocketboost for wireless surround sound and wireless subwoofer in your home theater, then set Wireless Sur and Wireless SW to On. If you are using Rocketboost Wireless to send the front left/right speaker audio signals to Rocketboost receivers in other rooms of your house, and not for your left/right home theater speakers, then set Wireless Front to Off. Option Wireless Front Wireless Sur Wireless SW Configuration On or Off On or Off On or Off Setting speaker distance (Sp Distance menu) Lets you specify the distance from each speaker to the listening position so that the sound from each speaker arrives at the listener's ears as the sound designer intended. 16 www.insigniaproducts.com