Insignia NSHT511 User Manual (English) - Page 23

Presetting FM or AM stations, Using the listening modes

Page 23 highlights

Insignia NS-HT511 Home Theater System Tip You can also press the TUNE MODE and arrow buttons on the remote control. - OR • To manually tune to a station: • Press TUNING MODE until the AUTO indicator goes off. • Press and hold TUNING or . The receiver tunes up or down the frequency band as long as you hold the button. Press the button repeatedly to tune up or down by steps. Tip • In Manual Tuning mode, FM stations are in mono. • If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to Manual Tuning mode and listen to the station in mono. • You can also press the TUN MODE and arrow buttons on the remote control. - OR • To tune to a station by entering the frequency: • Using the remote control, press TUNER repeatedly to select AM or FM, then press D.TUN. • Within eight seconds, press the number buttons to enter the frequency of the radio station you want. For example, to tune to 87.50, press 8, 7, then 5. Presetting FM or AM stations You can store a combination of as many as 40 of your favorite AM or FM stations as presets. To store a station as a preset: 1 Tune to the FM or AM station that you want to store as a preset. See "Listening to the radio" on page 18 for information on tuning your receiver. 2 Press MEMORY. The preset number flashes. 3 While the preset number is flashing (about eight seconds), press PRESET or to select a preset number from one through 40. 4 Press MEMORY again to store the station or channel. The station or channel is stored and the preset number stops flashing. 5 Repeat steps 1 through 4 to preset your favorite radio stations. Tuning to a preset station To tune to a preset station: • To select a preset, press PRESET or on the receiver, or press CH +/- on the remote control. Tip You can also press the number buttons on the remote control to select a preset station directly. Deleting preset stations To delete a preset station: 1 Select the preset you want to delete. 2 Press TUNING MODE while pressing and holding MEMORY. The preset is deleted and its number disappears from the display. Using the listening modes Notes • • • • You can only select the Dolby Digital and DTS listening modes if your Blu-ray Disc/DVD player is connected to the receiver with a digital audio connection (coaxial, optical, or HDMI). The listening mode you can select depends on the format of the input signal. To check the format, see "Displaying source information" on page 17. You can only select Mono, Direct, and Stereo listening modes with a pair of headphones is connected. Listening modes cannot be selected while a pair of headphones is connected. The receiver's listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound. The following audio formats are supported by the listening modes: • MONO-This is mono (monophonic) sound. All the audio signals are mixed and reproduced through a single speaker. • STEREO-This is stereo (stereophonic) sound. Two independent audio signal channels are reproduced through two speakers. • 5.1ch-This is 5.1-channel surround sound. This receiver has five main channels of sound and a sixth subwoofer channel (called the point-one channel). • 7.1ch-This is 7.1-channel surround sound. This is a further sound enhancement to 5.1 channel sound with two additional speakers that provide greater sound envelopment and more accurate positioning of sounds. The receiver outputs this source in 5.1-channel surround sound. Selecting a listening mode To select a listening mode: • Press one of the following buttons. If you are using the remote control, press the RECEIVER button first. See "Listening modes" on page 20, and "Insignia-Original Listening Modes" on page 21 for information on listening modes. • MOVIE/TV-This button selects the listening modes intended for use with movies and TV. • MUSIC-This button selects the listening modes intended for use with music. • GAME-This button selects the listening modes intended for use with video games. • STEREO-This button selects the Stereo listening mode and All Channel Stereo listening mode. www.insigniaproducts.com 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42

19
Insignia NS-HT511 Home Theater System
www.insigniaproducts.com
- OR -
To manually tune to a station:
• Press
TUNING MODE
until the AUTO
indicator goes off.
Press and hold
TUNING
or
. The
receiver tunes up or down the frequency
band as long as you hold the button. Press
the button repeatedly to tune up or down
by steps.
- OR -
To tune to a station by entering the frequency:
Using the remote control, press
TUNER
repeatedly to select
AM
or
FM
, then press
D.TUN
.
Within eight seconds, press the number
buttons to enter the frequency of the radio
station you want. For example, to tune to
87.50, press
8
,
7
, then
5
.
Presetting FM or AM stations
You can store a combination of as many as 40 of
your favorite AM or FM stations as presets.
To store a station as a preset:
1
Tune to the FM or AM station that you want to
store as a preset. See “Listening to the radio” on
page 18 for information on tuning your receiver.
2
Press
MEMORY
. The preset number flashes.
3
While the preset number is flashing (about eight
seconds), press
PRESET
or
to select a
preset number from one through 40.
4
Press
MEMORY
again to store the station or
channel. The station or channel is stored and the
preset number stops flashing.
5
Repeat steps 1 through 4 to preset your favorite
radio stations.
Tuning to a preset station
To tune to a preset station:
To select a preset, press
PRESET
or
on
the receiver, or press
CH +/–
on the remote
control.
Deleting preset stations
To delete a preset station:
1
Select the preset you want to delete.
2
Press
TUNING MODE
while pressing and
holding
MEMORY
. The preset is deleted and its
number disappears from the display.
Using the listening modes
The receiver’s listening modes can transform your
listening room into a movie theater or concert hall,
with high fidelity and stunning surround sound.
The following audio formats are supported by the
listening modes:
MONO
–This is mono (monophonic) sound. All the
audio signals are mixed and reproduced through
a single speaker.
STEREO
–This is stereo (stereophonic) sound. Two
independent audio signal channels are
reproduced through two speakers.
5.1ch
–This is 5.1-channel surround sound. This
receiver has five main channels of sound and a
sixth subwoofer channel (called the point-one
channel).
7.1ch
–This is 7.1-channel surround sound. This is
a further sound enhancement to 5.1 channel
sound with two additional speakers that provide
greater sound envelopment and more accurate
positioning of sounds. The receiver outputs this
source in 5.1-channel surround sound.
Selecting a listening mode
To select a listening mode:
Press one of the following buttons. If you are
using the remote control, press the
RECEIVER
button first. See “Listening modes” on page 20,
and “Insignia-Original Listening Modes” on page
21 for information on listening modes.
MOVIE/TV
–This button selects the listening
modes intended for use with movies and TV.
MUSIC
–This button selects the listening
modes intended for use with music.
GAME
–This button selects the listening
modes intended for use with video games.
STEREO
–This button selects the Stereo
listening mode and All Channel Stereo
listening mode.
Tip
You can also press the
TUNE MODE
and arrow
buttons on the remote control.
Tip
In Manual Tuning mode, FM stations are in
mono.
If the signal from a stereo FM station is weak, it
may be impossible to get good reception. In this
case, switch to Manual Tuning mode and listen
to the station in mono.
You can also press the
TUN MODE
and arrow
buttons on the remote control.
Tip
You can also press the number buttons on the
remote control to select a preset station directly.
Notes
You can only select the Dolby Digital and DTS
listening modes if your Blu-ray Disc/DVD player
is connected to the receiver with a digital audio
connection (coaxial, optical, or HDMI).
The listening mode you can select depends on
the format of the input signal. To check the
format, see “Displaying source information” on
page 17.
You can only select
Mono
,
Direct
, and
Stereo
listening modes with a pair of headphones is
connected.
Listening modes cannot be selected while a pair
of headphones is connected.