Intel S5500HV Product Specification - Page 29

Serial ATA Support, 4.1.2, Integrated RAID Support

Get Intel S5500HV PDF manuals and user guides View all Intel S5500HV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Functional Architecture Intel® Server Board S5500HV/Intel® Server System SR1670HV TPS 3.4.1.1 Serial ATA Support The ICH10R has an integrated Serial ATA (SATA) controller that supports independent DMA operation on four ports with data transfer rates of up to 3.0 Gb/s. The four SATA ports on the server board are numbered SATA-1 through SATA-4. The SATA ports can be enabled or disabled and/or configured by accessing the BIOS setup utility during POST. 3.4.1.2 Integrated RAID Support The server board has embedded support for two RAID options: ƒ Intel® Matrix Storage Manager with support for RAID levels 0, 1, 5, and 10 (Windows* support only) ƒ LSI* MegaRAID (Default) with support for RAID levels 0, 1, and 10 (Windows* and Linux) By default the server board is configured to support the LSI* MegaRAID option. To change this, a jumper block on the board needs to be changed. The following diagram shows the location of the jumper block and its settings. 1 1 2 2 3 3 LSI Intel (Default) Figure 11. RAID Option Jumper Block By default, BIOS does NOT enable RAID support. To enable this feature, on option in BIOS setup must be set as described in the following procedure: 1. Enter BIOS Setup (F2 Key) during POST 2. Go to the MAIN menu > IDE Configuration, and press 3. Set the Configure SATA As option to [RAID] 4. Save changes and then exit BIOS Setup Note: Refer to Intel® Server System SR1670HV Service Guide for RAID setup information Revision 1.2 Intel Confidential 20 Intel order number E69391-006

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Functional Architecture
Intel® Server Board S5500HV/Intel® Server System SR1670HV TPS
Revision 1.2
Intel Confidential
20
Intel order number E69391-006
3.4.1.1
Serial ATA Support
The ICH10R has an integrated Serial ATA (SATA) controller that supports independent DMA
operation on four ports with data transfer rates of up to 3.0 Gb/s. The four SATA ports on the
server board are numbered SATA-1 through SATA-4. The SATA ports can be enabled or
disabled and/or configured by accessing the BIOS setup utility during POST.
3.4.1.2
Integrated RAID Support
The server board has embedded support for two RAID options:
±
Intel
®
Matrix Storage Manager with support for RAID levels 0, 1, 5, and 10 (Windows*
support only)
±
LSI* MegaRAID (Default) with support for RAID levels 0, 1, and 10 (Windows* and Linux)
By default the server board is configured to support the LSI* MegaRAID option. To change this,
a jumper block on the board needs to be changed. The following diagram shows the location of
the jumper block and its settings.
Figure 11. RAID Option Jumper Block
By default, BIOS does NOT enable RAID support. To enable this feature, on option in BIOS
setup must be set as described in the following procedure:
1.
Enter BIOS Setup (F2 Key) during POST
2.
Go to the MAIN menu > IDE Configuration, and press <Enter>
3.
Set the Configure SATA As option to [RAID]
4.
Save changes and then exit BIOS Setup
Note:
Refer to
Intel
®
Server System SR1670HV Service Guide
for RAID setup information
1
2
3
1
2
3
LSI
(Default)
Intel