Intel SCB2 Product Guide - Page 18

Secure Mode, Summary of Software Security Features, Subsystem Group, menu. - board

Get Intel SCB2 - Server Board Motherboard PDF manuals and user guides
UPC - 735858148962
View all Intel SCB2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

• Must enter the supervisor password if you want to enter BIOS Setup or the SSU and have access to all of the options. • May enter either password to boot the server if Password on Boot is enabled in either the BIOS Setup or SSU. • May enter either password to exit secure mode. Secure Mode Configure and enable the secure boot mode by using the SSU. When secure mode is in effect: • You can boot the server and the operating system will run, but you must enter the user password to use the keyboard or mouse. • You cannot turn off system power or reset the server from the front panel switches. Secure mode has no effect on functions enabled via remote server management or power control via the watchdog timer. Taking the server out of secure mode does not change the state of system power. That is, if you press and release the power switch while secure mode is in effect, the system will not be powered off when secure mode is later removed. However, if the front panel power switch remains depressed when secure mode is removed, the server will be powered off. Summary of Software Security Features The table below lists the software security features and describes what protection each offers. In general, to enable or set the features listed here, you must run the SSU and go to the Security Subsystem Group, menu. The table also refers to other SSU menus and to the Setup utility. Table 4. Software Security Features Feature Description Secure mode How to enter secure mode: • Setting and enabling passwords automatically places the system in secure mode. • If you set a hot-key combination (through Setup), you can secure the system simply by pressing the key combination. This means you do not have to wait for the inactivity time-out period. When the system is in secure mode: The server can boot and run the operating system, but mouse and keyboard input is not accepted until the user password is entered. At boot time, if a CD is detected in the CD-ROM drive or a diskette in drive A, the system prompts for a password. When the password is entered, the server boots from CD or diskette and disables the secure mode. If there is no CD in the CD-ROM drive or diskette in drive A, the server boots from drive C and automatically goes into secure mode. All enabled secure mode features go into effect at boot time. To leave secure mode: Enter the correct password(s). Disable writing to diskette In secure mode, the server will not boot from or write to a diskette unless a password is entered. To write protect access to diskette whether the server is in secure mode or not, use the Setup main menu, Floppy Options, and specify Floppy Access as read only. continued 18 Intel Server Board SCB2 Product Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
18
Intel Server Board SCB2 Product Guide
•
Must enter the supervisor password if you want to enter BIOS Setup or the SSU and have
access to all of the options.
•
May enter either password to boot the server if Password on Boot is enabled in either the BIOS
Setup or SSU.
•
May enter either password to exit secure mode.
Secure Mode
Configure and enable the secure boot mode by using the SSU.
When secure mode is in effect:
•
You can boot the server and the operating system will run, but you must enter the user
password to use the keyboard or mouse.
•
You cannot turn off system power or reset the server from the front panel switches.
Secure mode has no effect on functions enabled via remote server management or power control
via the watchdog timer.
Taking the server out of secure mode does not change the state of system power.
That is, if you
press and release the power switch while secure mode is in effect, the system will not be powered
off when secure mode is later removed.
However, if the front panel power switch remains
depressed when secure mode is removed, the server will be powered off.
Summary of Software Security Features
The table below lists the software security features and describes what protection each offers.
In
general, to enable or set the features listed here, you must run the SSU and go to the Security
Subsystem Group, menu.
The table also refers to other SSU menus and to the Setup utility.
Table 4.
Software Security Features
Feature
Description
Secure mode
How to enter secure mode:
•
Setting and enabling passwords automatically places the system in secure
mode.
•
If you set a hot-key combination (through Setup), you can secure the system
simply by pressing the key combination.
This means you do not have to wait for
the inactivity time-out period.
When the system is in secure mode:
The server can boot and run the operating system, but mouse and keyboard input
is not accepted until the user password is entered.
At boot time, if a CD is detected in the CD-ROM drive or a diskette in drive A, the
system prompts for a password.
When the password is entered, the server boots
from CD or diskette and disables the secure mode.
If there is no CD in the CD-ROM drive or diskette in drive A, the server boots from
drive C and automatically goes into secure mode.
All enabled secure mode
features go into effect at boot time.
To leave secure mode:
Enter the correct password(s).
Disable writing to
diskette
In secure mode, the server will not boot from or write to a diskette unless a
password is entered.
To write protect access to diskette whether the server is in secure mode or not, use
the Setup main menu, Floppy Options, and specify Floppy Access as read only.
continued