Home » Intel Manuals » Motherboards » Intel SCB2 » Manual Viewer

Intel SCB2 Product Guide - Page 50

Server Menu, Feature, Choices, Description, Disabled, Enabled, Disable BSP, Last State

UPC - 735858148962

Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Security Menu (continued) Feature Choices Video Blanking Disabled Enabled Power Switch Inhibit Disabled Enabled Description Blank video when secure mode is activated. A pass word is required to unlock the system. This option only appears on the screen after a "user" password has been entered. When enabled, the power switch is inoperable. This option only appears on the screen after a "user" password has been entered. Server Menu Feature System Management Console Redirection Event Log Configuration Service Boot Assert NMI on PERR Assert NMI on SERR FRB-2 Policy BMC IRQ After Power Failure Temperature Sensor Choices Press Press Press Enable Disable Disabled Enabled Disabled Enabled Disable BSP Do not Disable BSP Retry 3 Times Disabled IRQ 5 IRQ 11 Stays Off Last State Power On Disabled Enabled POST Error Pause Platform Event Filtering Disabled Enabled Disabled Enabled Description Enters Submenu. Enters Submenu. Enters Submenu If enabled, server boots directly to System Management. If enabled, PCI bus parity error (PERR) routes to NMI. If enabled, PCI bus system error (SERR) routes to NMI. Controls the policy of the FRB-2 timeout. This option determines when the Boot Strap Processor (BSP) should be disabled if an FRB-2 error occurs. Sets the BMC IRQ. Determines the mode of operation if a power loss occurs. If enabled, the system will not boot if the ambient system temperature is outside the range specified in the Sensor Data Record (SDR). If enabled, the system will wait for user intervention on critical POST errors. Enable/Disable triggers for system sensor events inside the Baseboard Management Controller (BMC). 50 Intel Server Board SCB2 Product Guide

Section	Page
Intel® Server Board SCB2 Product Guide	1
Disclaimer	2
Contents	3
1 Description	7
Server Board Features	7
Server Board Connector and Component Locations	8
Back Panel Connectors	9
Processor	10
Memory	10
PCI Riser Slots	10
Video	11
SCSI Controller	11
ATA-100 Controller	11
IDE RAID	11
Network Controller	12
Network Teaming Features	12
Keyboard and Mouse	14
RJ-45 Serial Port	14
ACPI	16
Security	17
Intrusion Switch Monitoring	17
Software Locks	17
2 Installation Procedures	21
Install the I/O Shield	21
Rearrange the Standoffs	22
Server Board Bumpers	23
Install the Server Board	24
Installing Processors	25
Install the Processor Terminator	28
Memory	29
Connect Cables	30
3 Upgrading	31
Tools and Supplies Needed	31
Cautions	31
Memory	32
Processors	33
Adding or Replacing a Processor	34
Removing a Processor	37
Installing and Removing a Terminator	38
Replacing the Back up Battery	39
4 Configuration Software and Utilities	41
Service Partition (Optional)	41
Configuration Utilities	41
System Software Update Sequence	41
Hot Keys	42
Power-On Self-Test (POST)	43
Using BIOS Setup	43
Record BIOS Setup Settings	44
If BIOS Setup Is Inaccessible	44
BIOS Setup Menus	44
Main Menu	45
Advanced Menu	46
Security Menu	49
Server Menu	50
Boot Menu	52
Exit Menu	53
Temporarily Changing the Boot Device Priority	53
Permanently Changing the Boot Device Priority	54
Running the Adaptec SCSISelect Utility	54
When to Run the Adaptec SCSISelect Utility	54
Running the SCSISelect Utility	54
Configuring the Adaptec AIC-7899 SCSI Adapter	55
Running the Promise FastBuild Utility	55
When to Run the Promise FastBuild Utility	56
Running the Promise FastBuild Utility	56
Direct Platform Control (DPC) Console	56
DPC Console Modes of Operation	57
Running the DPC Console	57
Using the System Setup Utility	57
What You Need to Do	58
Running the SSU	58
Customizing the SSU	59
Launching a Task	60
MultiBoot Options Add-in	60
Password Add-in	60
SEL Manager Add-in	62
FRU Manager Add-in	63
SDR Manager Add-in	64
System Update Add-In	64
Configuration Save/Restore Add-In	65
Platform Event Manager Add-in	66
Exiting the SSU	74
Platform Event Paging	74
Using Platform Event Paging	74
Software Updates	75
Creating a Bootable Diskette	75
Software Update Package	75
Preparation	75
Extraction	76
Updating	76
Individual Updates	77
BIOS Upgrade Description	77
Firmware Update Utility Description	79
FRU/SDR Load Utility Description	79
5 Solving Problems	83
Resetting the System	83
Initial System Startup	83
Checklist	83
Running New Application Software	84
Checklist	84
After the System Has Been Running Correctly	84
Checklist	84
More Problem Solving Procedures	85
Preparing the System for Diagnostic Testing	85
Monitoring POST	85
Verifying Proper Operation of Key System Lights	85
Confirming Loading of the Operating System	85
Specific Problems and Corrective Actions	86
Power Light Does Not Light	86
No Characters Appear on Screen	86
Characters Are Distorted or Incorrect	87
System Cooling Fans Do Not Rotate Properly	87
Diskette Drive Activity Light Does Not Light	88
CD-ROM Drive Activity Light Does Not Light	88
Cannot Connect to a Server	88
Problems with Network	89
Problems with Application Software	90
Bootable CD-ROM Is Not Detected	90
6 Technical Reference	91
Server Board Jumpers	91
Diagnostic LEDs	92
7 Regulatory and Integration Information	97
Product Regulatory Compliance	97
Product Safety Compliance	97
Product EMC Compliance	97
Product Regulatory Compliance Markings	97
Electromagnetic Compatibility Notices	98
Europe (CE Declaration of Conformity)	98
Australian Communications Authority (ACA) (C- Tick Declaration of Conformity)	98
Ministry of Economic Development (New Zealand) Declaration of Conformity	98
BSMI (Taiwan)	98
8 Equipment Log and Power Consumption Worksheets	99
Equipment Log	99
Current Usage	101
Calculating Power Consumption	101