Intel SR2520SAFNA User Guide - Page 61

Removing Retention Device from Drive Carrier SR2520SAX, SR2520SAXS and SR2520SAXR/

Get Intel SR2520SAFNA - Server System - 0 MB RAM PDF manuals and user guides
UPC - 735858191036
View all Intel SR2520SAFNA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

4. Remove the four screws that attach the plastic retention device or the previously installed hard drive to the drive carrier. Two screws are at each side of the retention device or the hard drive. Store the plastic retention device for future use. See letter "A" in the figure below. 5. Remove the hard drive from its wrapper and place it on an antistatic surface. 6. Set any jumpers and/or switches on the drive according to the drive manufacturer's instructions. 7. With the drive circuit-side down, position the connector end of the drive so that it is facing the rear of the drive carrier. 8. Align the holes in the drive to the holes in the drive carrier and attach it to the carrier with the screws that were attached to the plastic retention device. See letter "B" in the figure below. A B AF001451 Figure 27. Removing Retention Device from Drive Carrier (SR2520SAX/ SR2520SAXS and SR2520SAXR/SR2520SAXSR) 9. With the black lever in the fully open position, slide the drive assembly into the server system (see letter "A" in the figure below). The green latch at the front of the drive carrier must be to the right. Do not push on the black drive carrier lever until the lever begins to close by itself. 10. When the black drive carrier lever begins to close by itself, push on it to lock the drive assembly into place (see letter "B" in the figure below). Intel® Server System SR2520SA User's Guide 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
Intel
®
Server System SR2520SA User’s Guide
39
4.
Remove the four screws that attach the plastic retention device or the previously
installed hard drive to the drive carrier. Two screws are at each side of the retention
device or the hard drive. Store the plastic retention device for future use. See letter
“A” in the figure below.
5.
Remove the hard drive from its wrapper and place it on an antistatic surface.
6.
Set any jumpers and/or switches on the drive according to the drive manufacturer's
instructions.
7.
With the drive circuit-side down, position the connector end of the drive so that it is
facing the rear of the drive carrier.
8.
Align the holes in the drive to the holes in the drive carrier and attach it to the
carrier with the screws that were attached to the plastic retention device. See letter
“B” in the figure below.
Figure 27. Removing Retention Device from Drive Carrier (SR2520SAX/
SR2520SAXS and SR2520SAXR/SR2520SAXSR)
9.
With the black lever in the fully open position, slide the drive assembly into the
server system (see letter “A” in the figure below). The green latch at the front of the
drive carrier must be to the right. Do not push on the black drive carrier lever until
the lever begins to close by itself.
10.
When the black drive carrier lever begins to close by itself, push on it to lock the
drive assembly into place (see letter “B” in the figure below).
A
B
AF001451