Intermec PD42 PD41 and PD42 Commercial Printer User's Manual - Page 42

General Tasks, Add Printer, Printer Tasks, Wireless Setup Wizard

Get Intermec PD42 PDF manuals and user guides View all Intermec PD42 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Chapter 2 - Connecting the Printer 3 If necessary, change the PC serial port configuration to match your printer: Parameter Baud rate Data bits Parity Stop bits Default Setting 9600 8 None 1 4 Start PrintSet on your PC. 5 In the General Tasks box, click Add Printer and step through the screens of the Add Printer Wizard until you have successfully added your printer. 6 In the Printer Tasks box, click Wireless Setup Wizard and step through the screens to set up wireless network and security parameters. To set up the printer for wireless communications using HyperTerminal 1 Connect one end of the serial cable to the back of the printer and connect the other end of the cable to a serial COM port on the PC. 2 On your PC, open HyperTerminal and set these serial port parameters: Parameter Baud rate Data bits Parity Stop bits Default Setting 9600 8 None 1 . 3 From the host PC, check the wireless settings. For help, see "Manually Configuring IP Settings" on page 25. If you are using IPL, send these commands to the printer: wt,SSID wt,WEP 28 PD41 and PD42 Commercial Printer User's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
Chapter 2 — Connecting the Printer
28
PD41 and PD42 Commercial Printer User’s Manual
3
If necessary, change the PC serial port configuration to match
your printer:
4
Start PrintSet on your PC.
5
In the
General Tasks
box, click
Add Printer
and step through the
screens of the Add Printer Wizard until you have successfully
added your printer.
6
In the
Printer Tasks
box, click
Wireless Setup Wizard
and step
through the screens to set up wireless network and security
parameters.
To set up the printer for wireless communications using
HyperTerminal
1
Connect one end of the serial cable to the back of the printer and
connect the other end of the cable to a serial COM port on the PC.
2
On your PC, open HyperTerminal and set these serial port
parameters:
.
3
From the host PC, check the wireless settings. For help, see
“Manually Configuring IP Settings” on page 25
.
If you are using IPL, send these commands to the printer:
<STX><SI>wt,SSID<ETX>
<STX><SI>wt,WEP<ETX>
Parameter
Default Setting
Baud rate
9600
Data bits
8
Parity
None
Stop bits
1
Parameter
Default Setting
Baud rate
9600
Data bits
8
Parity
None
Stop bits
1