Intermec SR31T SR31T Tethered Scanner User's Guide - Page 39

Wand Emulation, Connecting a Wand Emulation Cable, Setting up the Wand Emulation Interface

Get Intermec SR31T PDF manuals and user guides View all Intermec SR31T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Chapter 3 - SR31T Interfaces Wand Emulation The SR31T can be connected to a host using a wand emulation cable. See the "SR31T Cable List" on page 6 for a list of part numbers for the different cables. The type of cable depends on the host device or intermec computer your are using. No power supply is necessary. Connecting a Wand Emulation Cable To create a wand emulation connection 1 Turn off your host device or Intermec computer. 2 Connect the wand emulation cable to your SR31T and the host or Intermec computer. 3 If necessary, use the configuration bar codes in the next section to configure your SR31T for wand emulation interface. Setting up the Wand Emulation Interface This section provides configuration bar codes for a basic setup. All bar codes marked with (*) indicate the default value. For more configuration options see Chapter 4, "Configuring the SR31T Scanner" on page 33. Logical Signal State During Transmission Bar = 0, Space = 1 (*) Bar = 1, Space = 0 Note: When using a wand emulation connection the postamble and preamble are not available. SR31T Tethered Scanner User's Guide 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Chapter 3 — SR31T Interfaces
SR31T Tethered Scanner User’s Guide
31
Wand Emulation
The SR31T can be connected to a host using a wand emulation cable.
See the
“SR31T Cable List” on page 6
for a list of part numbers for
the different cables. The type of cable depends on the host device or
intermec computer your are using. No power supply is necessary.
Connecting a Wand Emulation Cable
To create a wand emulation connection
1
Turn off your host device or Intermec computer.
2
Connect the wand emulation cable to your SR31T and the host or
Intermec computer.
3
If necessary, use the configuration bar codes in the next section to
configure your SR31T for wand emulation interface.
Setting up the Wand Emulation Interface
This section provides configuration bar codes for a basic setup. All bar
codes marked with (*) indicate the default value. For more
configuration options see
Chapter 4, "Configuring the SR31T
Scanner” on page 33
.
Logical Signal State During Transmission
Bar = 0, Space = 1 (*)
Bar = 1, Space = 0
Note:
When using a wand emulation connection the postamble and
preamble are not available.