Intermec SR31T SR31T Tethered Scanner User's Guide - Page 50

Rescuing the SR31T, To rescue your SR31T

Get Intermec SR31T PDF manuals and user guides View all Intermec SR31T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Chapter 5 - Troubleshooting and Maintaining the SR31T Rescuing the SR31T You can rescue your SR31T if you cannot configure it anymore because it is in a locked configuration. This can happen if you inadvertently disabled the trigger for example. Note: When you rescue your scanner, factory default settings are restored including custom default settings. Rescuing the scanner is also a way to force a factory reset if you do not have access to a Reset factory defaults configuration code or a PC with EasySet. To rescue your SR31T 1 Disconnect your product from its electrical power (disconnect the cable from the product). 2 With the product disconnected, use your usual operating hand to pull and hold the trigger. 3 Do not release the trigger while you reestablish electrical power (reconnect the cable). The scanner acknowledges power-up (beeps, LEDs and vibrate alert). 4 Keep the trigger pulled around 10 seconds until the red LED lights up. 5 Pull the trigger very rapidly five times in succession while the red LED is on (you need to be quick as the red LED only stays on for 2 seconds).  The green LED comes on and the scanner beeps a reset confirmation (beep melody), then acknowledges power-up again (beeps, vibrate alert). Note: If your scanner still does not operate correctly after a rescue procedure, contact your Intermec Product Support representative (see Calling Product Support in the next section). 42 SR31T Tethered Scanner User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Chapter 5 — Troubleshooting and Maintaining the SR31T
42
SR31T Tethered Scanner User’s Guide
Rescuing the SR31T
You can rescue your SR31T if you cannot configure it anymore
because it is in a locked configuration. This can happen if you
inadvertently disabled the trigger for example.
To rescue your SR31T
1
Disconnect your product from its electrical power (disconnect the
cable from the product).
2
With the product disconnected, use your usual operating hand to
pull and hold the trigger.
3
Do not release the trigger while you reestablish electrical power
(reconnect the cable).
The scanner acknowledges power-up (beeps, LEDs and vibrate
alert).
4
Keep the trigger pulled around 10 seconds until the red LED lights
up.
5
Pull the trigger very rapidly five times in succession while the red
LED is on (you need to be quick as the red LED only stays on for 2
seconds).
The green LED comes on and the scanner beeps a reset
confirmation (beep melody), then acknowledges power-up again
(beeps, vibrate alert).
Note:
When you rescue your scanner, factory default settings are
restored including custom default settings. Rescuing the scanner is
also a way to force a factory reset if you do not have access to a
Reset
factory defaults
configuration code or a PC with EasySet.
Note
: If your scanner still does not operate correctly after a rescue
procedure, contact your Intermec Product Support representative (see
Calling Product Support
in the next section).