Jenn-Air JGRP436HL Owners Manual - Page 19

To Insert Roll-Out Rack, V cutout, Rack guide, To Remove Roll-Out Rack, Oven Vent, Cooling Fan,

Get Jenn-Air JGRP436HL PDF manuals and user guides View all Jenn-Air JGRP436HL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

To Insert Roll-Out Rack 1. Angle the rack assembly up and insert the back edge into the "V" cutout in the rack guides of the oven cavity. 2. Keep the rack lifted at an angle and push in until the back edge of the sliding rails (A) bypass the lower "V" cutout. 3. Angle the rack downward and continue to gently slide the assembly in until the center brace (C) bypasses the "V" cutout. 4. Raise rack assembly to flat position and gently push to the back of the oven until the back edge of the sliding rail drops. 5. When placing racks in adjacent positions, start by loading the lower rack positions first and then install the rack in the position above it. 6. Pull the rack assembly slightly forward until the front edge drops and the sliding rails are on the rack guide. 2 1 1 "V" cutout 2 Rack guide 2 1 1 "V" cutout 2 Rack guide USING YOUR OVEN To Remove Roll-Out Rack 1. Push the sliding shelf in completely so that it is closed and engaged with the slide rails. 1 2 3 1 Sliding shelf 2 Slide rails 3 Rack 2. Using 2 hands, lift up on the front edge of the rack assembly. Slowly push the rack assembly to the back wall of the oven so the front edge of the sliding shelf sits on the rack guides on the side of the oven cavity. The front edge of the rack should be higher than the back edge. 3. Using 2 hands, lift up the back of the rack assembly so that the front and back are level on the rack guides. 4. Pull the rack assembly out. To avoid damage to the sliding shelves, do not place more than 25 lbs (11.4 kg) on the rack. Do not clean the roll-out rack in a dishwasher. It may remove the rack's lubricant and affect its ability to slide. See the "General Cleaning" section for more information. When placing racks in adjacent positions, start by loading the lower rack positions first and then installing the rack in the position immediately above it. Oven Vent The oven vent should not be blocked or covered since it allows the release of hot air and moisture from the oven. Blocking or covering the vent will cause poor air circulation, affecting cooking and cleaning results. Do not set plastics, paper, or other items that could melt or burn near the oven vent. 1 1 Oven vent Cooling Fan The oven has a dual speed cooling fan motor. When the oven temperature is in the Self-Cleaning cycle, the fan will operate at its highest speed to increase airflow and better exhaust the hotter air through the oven vent(s). An increase in noise may be noticeable until the oven cools. NOTE: Cooling fan may continue to run after the oven has been turned off. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
19
USING YOUR OVEN
To Insert Roll-Out Rack
1.
Angle the rack assembly up and insert the back edge into
the “V” cutout in the rack guides of the oven cavity.
2.
Keep the rack lifted at an angle and push in until the back
edge of the sliding rails (A) bypass the lower “V” cutout.
3.
Angle the rack downward and continue to gently slide the
assembly in until the center brace (C) bypasses the “V”
cutout.
4.
Raise rack assembly to flat position and gently push to
the back of the oven until the back edge of the sliding rail
drops.
5.
When placing racks in adjacent positions, start by loading
the lower rack positions first and then install the rack in the
position above it.
6.
Pull the rack assembly slightly forward until the front edge
drops and the sliding rails are on the rack guide.
1
2
1
“V” cutout
2
Rack guide
1
2
1
“V” cutout
2
Rack guide
To Remove Roll-Out Rack
1.
Push the sliding shelf in completely so that it is closed and
engaged with the slide rails.
2.
Using 2 hands, lift up on the front edge of the rack
assembly. Slowly push the rack assembly to the back wall
of the oven so the front edge of the sliding shelf sits on the
rack guides on the side of the oven cavity. The front edge of
the rack should be higher than the back edge.
3.
Using 2 hands, lift up the back of the rack assembly so that
the front and back are level on the rack guides.
4.
Pull the rack assembly out.
To avoid damage to the sliding shelves, do not place more than
25 lbs (11.4 kg) on the rack.
Do not clean the roll-out rack in a dishwasher. It may remove
the rack’s lubricant and affect its ability to slide.
See the “General Cleaning” section for more information.
When placing racks in adjacent positions, start by loading the
lower rack positions first and then installing the rack in the
position immediately above it.
Oven Vent
The oven vent should
not be blocked or covered
since it allows the
release of hot air and
moisture from the oven.
Blocking or covering the
vent will cause poor air
circulation, affecting
cooking and cleaning
results. Do not set plastics,
paper, or other items that
could melt or burn near
the oven vent.
Cooling Fan
The oven has a dual speed cooling fan motor.
When the oven temperature is in the Self-Cleaning cycle, the fan
will operate at its highest speed to increase airflow and better
exhaust the hotter air through the oven vent(s). An increase in
noise may be noticeable until the oven cools.
NOTE:
Cooling fan may continue to run after the oven has been
turned off.
1
2
3
1
Sliding shelf
2
Slide rails
3
Rack
1
1
Oven vent