Jenn-Air JGS8850CDS Installation Instruction - Page 11

Adjust Flame Height, Check Operation of Oven Bake Burner

Get Jenn-Air JGS8850CDS PDF manuals and user guides View all Jenn-Air JGS8850CDS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Adjust Flame Height Adjust the height of top burner flames. The cooktop "low" burner flame should be a steady blue flame approximately ¼" (0.64 cm) high. A B A. Low flame B. High flame To adjust standard burners: The flame can be adjusted using the adjustment screw in the center of the valve stem. The valve stem is located directly underneath the control knob. If the "low" flame needs to be adjusted: 1. Light 1 burner and turn to lowest setting. 2. Remove the control knob. Hold the knob stem in the low position using a pair of pliers. Use an ¹⁄₈" (3.0 mm) flat-blade screwdriver to turn the screw located in the center of the control knob stem until the flame is the proper size. 3. Replace the control knob. 4. Test the flame by turning the control from "LO" to "HI," checking the flame at each setting. 5. Repeat above steps for each burner. To adjust double burner: 1. Light burner and turn to lowest setting where both inner and outer burners are lit. 2. Remove the control knob. Insert an ¹⁄₈" (3.0 mm) flat-blade screwdriver into adjustment locations shown in the following illustration and engage the slotted screw. Turn the screw until the flame is the proper size. OFF HIGH 3. Replace the control knob. 4. Test the flame by turning the control from "LO" to "HI," checking the flame at each setting. Check Operation of Oven Bake Burner 1. Remove the oven rack. 2. Using a Phillips screwdriver, remove the 2 bake burner cover screws. 3. Lift up on rear of bake burner cover and remove. 4. Place bake burner cover on a covered surface. A B A. Bake burner cover B. Bake burner cover screws 5. Press BAKE. "BAKE" and temperatures will show in the display. 6. Press either Quickset pad or the control panel next to the temperature on the display. The igniter used to light the bake burner will glow. Once the igniter is hot, the oven bake burner should light. Under certain conditions, it may take up to 60 seconds for it to light. Adjust Oven Bake Burner Flame (if needed) 1. Remove storage drawer or warming drawer. 2. Remove access panel (2 screws) located on the rear wall, inside the storage drawer compartment. 3. Check the oven bake burner for proper flame. This flame should have a ½" (1.3 cm) long inner cone of bluish-green, with an outer mantle of dark blue, and should be clean and soft in character. No yellow tips, blowing or lifting of flame should occur. 4. If the oven bake flame needs to be adjusted, locate the air shutter near the center rear of the range. Use a flat-blade screwdriver to loosen the air shutter adjustment screw. Rotate the air shutter until the proper flame appears. Tighten air shutter adjustment screw. A B A. Air shutter adjustment screw B. Air shutter 5. Press CANCEL when finished. 6. Reinstall access panel and oven bake burner cover. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
11
Adjust Flame Height
Adjust the height of top burner flames. The cooktop “low” burner
flame should be a steady blue flame approximately ¼" (0.64 cm)
high.
To adjust standard burners:
The flame can be adjusted using the adjustment screw in the
center of the valve stem. The valve stem is located directly
underneath the control knob.
If the “low” flame needs to be adjusted:
1.
Light 1 burner and turn to lowest setting.
2.
Remove the control knob.
Hold the knob stem in the low position using a pair of pliers. Use
an
¹⁄₈
" (3.0 mm) flat-blade screwdriver to turn the screw located in
the center of the control knob stem until the flame is the proper
size.
3.
Replace the control knob.
4.
Test the flame by turning the control from “LO” to “HI,”
checking the flame at each setting.
5.
Repeat above steps for each burner.
To adjust double burner:
1.
Light burner and turn to lowest setting where both inner and
outer burners are lit.
2.
Remove the control knob.
Insert an
¹⁄₈
" (3.0 mm) flat-blade screwdriver into adjustment
locations shown in the following illustration and engage the
slotted screw. Turn the screw until the flame is the proper size.
3.
Replace the control knob.
4.
Test the flame by turning the control from “LO” to “HI,”
checking the flame at each setting.
Check Operation of Oven Bake Burner
1.
Remove the oven rack.
2.
Using a Phillips screwdriver, remove the 2 bake burner cover
screws.
3.
Lift up on rear of bake burner cover and remove.
4.
Place bake burner cover on a covered surface.
5.
Press BAKE. “BAKE” and temperatures will show in the
display.
6.
Press either Quickset pad or the control panel next to the
temperature on the display.
The igniter used to light the bake burner will glow. Once the
igniter is hot, the oven bake burner should light. Under certain
conditions, it may take up to 60 seconds for it to light.
Adjust Oven Bake Burner Flame (if needed)
1.
Remove storage drawer or warming drawer.
2.
Remove access panel (2 screws) located on the rear wall,
inside the storage drawer compartment.
3.
Check the oven bake burner for proper flame.
This flame should have a ½" (1.3 cm) long inner cone of
bluish-green, with an outer mantle of dark blue, and should
be clean and soft in character. No yellow tips, blowing or
lifting of flame should occur.
4.
If the oven bake flame needs to be adjusted, locate the air
shutter near the center rear of the range. Use a flat-blade
screwdriver to loosen the air shutter adjustment screw.
Rotate the air shutter until the proper flame appears. Tighten
air shutter adjustment screw.
5.
Press CANCEL when finished.
6.
Reinstall access panel and oven bake burner cover.
A. Low flame
B. High flame
A
B
A. Bake burner cover
B. Bake burner cover screws
A. Air shutter adjustment screw
B. Air shutter
A
B
A
B