Kenmore 2029915 Use and Care Manual - Page 20

To Clean, Agitator

Get Kenmore 2029915 - Canister Vacuum PDF manuals and user guides View all Kenmore 2029915 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

TO CLEAN AGITATOR: NOTE: In order to keep cleaning efficiency high and to prevent damage to your vacuum cleaner, the agitator must be cleaned every+ time the belt is changed. The agitator must also be cleaned according to the following schedule: Vacuum Cleaner Use _itator HEAVY (used daily) MODERATE (used 2-3 timeslweek) LIGHT + (used I time/week) every week eveF_ every 2 months_ IMPORTANT Turn off and unplug vacuum cleaner from electrical outlet, Check and remove hair, string and lint build-up frequently in the PowerMate agitator and end cap areas. Remove any dirt or debris in the belt path area or in the brush roller area,, Carefully remove any stdng or debris located on the agitator or end caps, AGITATOR ASSEMBLY then over be path. Drive Agitator End Cap NOTE: See PARTS AND FEATURES for Belt number, 2oPlace agitator assembly into PowerMate. 3. NOTE: On dirt sensor models be sure that the dirt sensor board is upright and the wires are tucked back in place 4+ Line up front of cover and base Rest cover on front edge of base as shown, 5. Rotate cover back., Press cover firmly until side latches snap into place+ "", _ End Cap Belt Path q Brush Unit End Cap _ 6. Make sure there is no gap between the cover and base and that the rear latches are snapped in place,, 7, Turn PowerMate upside down and replace two (2) cover screws, 2O

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
TO CLEAN
AGITATOR:
NOTE: In order to keep cleaning efficiency
high and to prevent damage to your vacuum
cleaner, the agitator must be cleaned every+
time
the
belt is changed.
The agitator must also be cleaned accord-
ing to the following schedule:
Vacuum
Cleaner
Use
HEAVY
-
(used daily)
MODERATE -
(used 2-3 timeslweek)
LIGHT +
(used I time/week)
_itator
every week
eveF_
every 2 months_
IMPORTANT
Turn
off
and unplug
vacuum cleaner
from
electrical
outlet,
Check and remove hair,
string and lint build-up frequently in the
PowerMate
agitator and end cap areas.
Remove
any dirt or debris in the belt path
area or in the brush roller area,,
Carefully
remove
any stdng or debris
located
on the agitator or end caps,
AGITATOR
ASSEMBLY
_
End
Cap
Belt
Path
q
Brush
Unit
End
Cap
_
then over be
path.
Drive
Agitator
End
Cap
NOTE: See
PARTS
AND FEATURES for
Belt number,
2o
Place agitator
assembly into
PowerMate.
3.
NOTE:
On dirt sensor models be sure
that the dirt sensor board
is
upright and the
wires are tucked back
in
place
4+Line up front of cover and base
Rest
cover on front edge of base as shown,
5.
Rotate cover
back., Press cover
firmly until side
latches snap into
place+
"",
6. Make sure there is no gap between the
cover and base and that the rear latches
are snapped in place,,
7,
Turn PowerMate upside down and
replace two (2) cover screws,
2O