Kenwood KMR-M506DAB Instruction Manual - Page 42

Connect external components, Installing the DAB antenna, CAUTION

Get Kenwood KMR-M506DAB PDF manuals and user guides View all Kenwood KMR-M506DAB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Installation/Connection Connect external components Installing the DAB antenna Connect the DAB antenna to the DAB antenna jack. (See the left column.) • DAB antenna is supplied for . For details, see the following. • For , you need to purchase the DAB antenna separately. For details, refer to the instruction manual supplied with the DAB antenna. No Part 1 Microphone input jack (Page 17) 2 Output terminals FRONT: Front output (2-way crossover) / Mid Range output (3-way crossover) REAR/SW: Rear/subwoofer output (2-way crossover) / Woofer output (3-way crossover) • When connecting an external amplifier to the output terminals of this unit, securely connect the amplifier ground wire to the car chassis to prevent damage to the unit. 3 DAB antenna jack (Page 7, 37) CAUTION • The film antenna (F) is exclusively for use inside the vehicle. • Do not install at the following locations: - where it may block the driver's view. - where it may obstruct the operation of safety devices such as air bags. - on movable glass surfaces such as the rear hatch. - at side of vehicle (e.g. door, front quarter window). - on rear window. • Signal strength will weaken when installed at the following locations: - on IR reflecting glass or locations covered with mirror type glass film. - where it overlaps with genuine radio antenna (pattern). - where it overlaps with window heating wires. - on glass that blocks radio signals (e.g. IR reflecting glass, thermal insulation glass). • Poor reception may occur: - due to noise when windscreen wiper, air conditioner, or motor is turned on. - depending on the direction of the broadcast station with respect to the vehicle (antenna). • Thoroughly wipe oil and dirt from the pasting surface with the supplied cleaner (I). • Do not bend or damage the film antenna (F). • It may not be possible to install on certain vehicles. • Check the cable routing of the film antenna (F) and amplifier unit (G) before pasting. • Do not apply any glass cleaner after pasting the film antenna (F). 34 ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
34
ENGLISH
Connect external components
No
Part
1
Microphone input jack (Page 17)
2
Output terminals
FRONT: Front output (2-way crossover) / Mid Range output (3-way crossover)
REAR/SW: Rear/subwoofer output (2-way crossover) / Woofer output (3-way crossover)
•
When connecting an external amplifier to the output terminals of this unit, securely
connect the amplifier ground wire to the car chassis to prevent damage to the unit.
3
DAB antenna jack (Page 7, 37)
Installation/Connection
Installing the DAB antenna
Connect the DAB antenna to the DAB antenna jack. (See the left column.)
• DAB antenna is supplied for
.
For details, see the following.
• For
, you need to purchase the DAB antenna separately.
For details, refer to the instruction manual supplied with the DAB antenna.
CAUTION
• The film antenna (F) is exclusively for use inside the vehicle.
• Do not install at the following locations:
– where it may block the driver’s view.
– where it may obstruct the operation of safety devices such as air bags.
– on movable glass surfaces such as the rear hatch.
– at side of vehicle (e.g. door, front quarter window).
– on rear window.
• Signal strength will weaken when installed at the following locations:
– on IR reflecting glass or locations covered with mirror type glass film.
– where it overlaps with genuine radio antenna (pattern).
– where it overlaps with window heating wires.
– on glass that blocks radio signals (e.g. IR reflecting glass, thermal
insulation glass).
• Poor reception may occur:
– due to noise when windscreen wiper, air conditioner, or motor is turned
on.
– depending on the direction of the broadcast station with respect to the
vehicle (antenna).
• Thoroughly wipe oil and dirt from the pasting surface with the supplied
cleaner (I).
• Do not bend or damage the film antenna (F).
• It may not be possible to install on certain vehicles.
• Check the cable routing of the film antenna (F) and amplifier unit (G)
before pasting.
• Do not apply any glass cleaner after pasting the film antenna (F).