Kodak BC4601 Service Manual - Page 28

Adjusting the Focus Light Path - Auto Focus Models Adjustment Specification

Get Kodak BC4601 - Carousel 4600 Projector PDF manuals and user guides
UPC - 041771125318
View all Kodak BC4601 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

SERVICE MANUAL SLIDE LIFT LEVER GUAGE TL-3001 SLIDE LIFT LEVER SELECT LEVER (not shown) A091_0016BCA A091_0016BA Adjusting the Focus Light Path - Auto Focus Models Adjustment Specification Seat AUTO-FOCUS TARGET SLIDE TL-3002 on the GATE MECHANISM. Use TL-3005 or TL-1165 to bend the AUTO-FOCUS BRACKET ASSEMBLY MIRROR until the image is within the target of the TARGET SLIDE. Warning Dangerous Voltage [1] Disconnect the main power. [2] Remove the PROJECTION LENS. [3] Do the removal for the LOWER HOUSING ASSEMBLY. Important It is necessary to make a FAN COVER TOOL. See the Tools section. [4] Install the FAN COVER TOOL over the FAN area and the LAMP MODULE. [5] Energize the projector. [6] Set the projector to the LOW LAMP position. [7] Install the AUTO-FOCUS TARGET SLIDE TL-3002 until it is fully seated in the GATE MECHANISM. [8] Look through the PROJECTION LENS hole and observe the focus light path on the AUTO-FOCUS TARGET SLIDE TL-3002. [9] Check the position of the image on the AUTO-FOCUS TARGET SLIDE TL-3002. 28 18NOV97 - SM5440-1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
SERVICE MANUAL
28
18NOV97 – SM5440-1
Adjusting the Focus Light Path - Auto Focus Models
Adjustment Specification
Seat AUTO-FOCUS TARGET SLIDE TL-3002 on the GATE MECHANISM.
Use TL-3005 or TL-1165 to bend the
AUTO-FOCUS BRACKET ASSEMBLY MIRROR until
the image is within the target of the TARGET SLIDE.
Warning
Dangerous Voltage
[1]
Disconnect the main power.
[2]
Remove the PROJECTION LENS.
[3]
Do the removal for the LOWER HOUSING ASSEMBLY.
Important
It is necessary to make a FAN COVER TOOL.
See the Tools section.
[4]
Install the FAN COVER TOOL over the FAN area and the LAMP MODULE.
[5]
Energize the projector.
[6]
Set the projector to the LOW LAMP position.
[7]
Install the AUTO-FOCUS TARGET SLIDE TL-3002 until it is fully seated in the GATE MECHANISM.
[8]
Look through the PROJECTION LENS hole and observe the focus light path on the AUTO-FOCUS TARGET
SLIDE TL-3002.
[9]
Check the position of the image on the AUTO-FOCUS TARGET SLIDE TL-3002.
A091_0016BA
TL-3001
LEVER GUAGE
SLIDE LIFT
SELECT
A091_0016BCA
(not shown)
LEVER
SLIDE LIFT
LEVER