Home » Kodak Manuals » Projectors » Kodak BC4601 » Manual Viewer

Kodak BC4601 Service Manual - Page 30

Adjusting the PHOTOCELL, Important, Warning

UPC - 041771125318

Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

SERVICE MANUAL Important If you cannot obtain the NULL position after doing the adjustment approximately 3 times, go to the adjustment procedure for the PHOTOCELL. light path T-BAR TL-3003 PROJECTION LENS NULL position TAB A091_4031BCA A091_4031BA AUTO-FOCUS TARGET SLIDE TL-3002 Adjustment Speciﬁcation Use TL-3002 and FAN CAP 232729 to check the adjustment of the PHOTOCELL. CLAMP LEVER PAD Adjusting the PHOTOCELL PHOTOCELL CIRCUIT BOARD wratten FILTER (2) Warning Dangerous Voltage [1] Disconnect the main power. [2] Do the removal for the LOWER HOUSING ASSEMBLY. Important It is necessary to make a FAN COVER TOOL. See the Tools section. [3] Install the FAN COVER TOOL over the FAN area and the LAMP MODULE. See the Tools section. POST (2) PHOTOCELL HOUSING PHOTOCELL MASK A091_4032GCA A091_4032GA 30 18NOV97 - SM5440-1

Section	Page
Library	4
Replacing the LOWER HOUSING ASSEMBLY	4
Installing the LOWER HOUSING ASSEMBLY	4
Replacing the FAN SHAFT ASSEMBLY	4
Installing the FAN SHAFT ASSEMBLY	6
Replacing the MOTOR	7
Installing the MOTOR	7
Replacing the WORM PULLEY and MECHANISM BELT	8
Installing the WORM PULLEY and MECHANISM BELT	9
Replacing the THERMAL FUSE ASSEMBLY	10
Installing the THERMAL FUSE ASSEMBLY	10
Replacing the LAMP MODULE RECEPTACLE	10
Installing the LAMP MODULE RECEPTACLE	11
Replacing the CYCLE SOLENOID ASSEMBLY	12
Installing the CYCLE SOLENOID ASSEMBLY	12
Replacing the MECHANISM ASSEMBLY	13
Installing the MECHANISM ASSEMBLY	13
Replacing the AUTO-FOCUS BRACKET ASSEMBLY	14
Installing the AUTO-FOCUS BRACKET ASSEMBLY	14
Replacing the CAM STACK ASSEMBLY and CYCLE LEVER ASSEMBLY	14
Installing the CAM STACK ASSEMBLY and CYCLE LEVER ASSEMBLY	17
Replacing the LAMP SOCKET TERMINAL ASSEMBLY	18
Installing the LAMP SOCKET TERMINAL ASSEMBLY	18
Replacing the LENS MOUNT ASSEMBLY - Auto Focus Model	19
Installing the LENS MOUNT ASSEMBLY - Auto Focus Models	19
Replacing the LENS MOUNT ASSEMBLY - Non Auto Focus Model	20
Installing the LENS MOUNT ASSEMBLY - Non Auto Focus Model	20
Replacing the AUTO-FOCUS SWITCH ASSEMBLY	21
Installing the AUTO-FOCUS SWITCH ASSEMBLY	21
Replacing the FOCUS SHAFT ASSEMBLY - Auto Focus Models	21
Installing the FOCUS SHAFT ASSEMBLY	23
Replacing the FOCUS SHAFT ASSEMBLY - Non Auto-Focus Models	23
Installing the FOCUS SHAFT ASSEMBLY	24
Section 2: Adjustments	25
Adjusting the CYCLE SOLENOID	25
Adjusting the INDEXER LEVER ASSEMBLY	26
Adjusting the SLIDE LIFT LEVER MANUAL, with MECHANISM Out	27
Adjusting the SLIDE LIFT LEVER POWER with Mechanism Out	27
Adjusting the Focus Light Path - Auto Focus Models Adjustment Specification	28
Adjusting the NULL	29
Adjusting the PHOTOCELL	30
Adjusting the CLAMP PAD ASSEMBLY	34
Adjusting the DARK SHUTTER	34
Section 3: Lubrication	36
Section 4: Tools	39
Section 5: Specifications	40
Section 6: Diagnostics	42
MAIN MOTOR Voltages	42
PHOTOCELL Voltages	43
5-PIN REMOTE CORD PLUG Voltages	43
SMALL COMPONENT BOARD ASSEMBLY 256809 Voltages	44
Voltage Specifications - General Parts	45
Power, Illumination, and Cooling Malfunctions	45
Slide Transport Malfunctions	46