Home » Konica Minolta Manuals » Printers » Konica Minolta AccurioPrint C3070L » Manual Viewer

Konica Minolta AccurioPrint C3070L AccurioPress C2070/C3080 Series Daily Maint - Page 28

How to Operate the Both Sides Adj. Item

View all Konica Minolta AccurioPrint C3070L manuals

Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

2.5 How to Operate the Both Sides Adj. Item 2 2.5 How to Operate the Both Sides Adj. Item 2.5.1 Finely adjust the side guide plates of the paper tray (for PF-707/PF-707m/PF602m) If front and rear side guide plates are not fixed upright, in other words, any gap is found between top and bottom edges of them, feeding trouble may be caused. In this case, follow the adjustment procedure below to properly fix the top and bottom edges of the side guide plates. 1 Withdraw the tray to be adjusted. % Trays cannot be withdrawn when the machine is not powered. Be sure to turn the sub power switch ON. 2 Fully widen the side guide plates and rear guide plate. % Turn the two side guide fixing knobs of the side guide plates counterclockwise to loosen them. % Fully widen the side guide plates and rear guide plate while pressing the lock release lever of the side guide plate and rear guide plate. NOTICE When moving the side guide plates, be sure to hold both the lock release lever of the front one and the handle of the rear one. If moved only with the front side guide plate, the side guide plates may not be fixed in position. 3 Load paper of the size to be adjusted. % Load about 100 sheets of paper. AccurioPress C2070/C2070P/C2060/C3080/C3080P/C3070, AccurioPrint C2060L/C3070L 2-7

Section	Page
Table of contents	4
1 Daily Care	7
1.1 About Daily Care	7
Care Timing	7
Care requirements	7
1.2 Cleaning the Duplex Part	8
1.3 Cleaning Main Body Tray	11
1.4 Cleaning Multi Bypass Tray MB-506 or Multi Bypass Tray MB-508	13
1.5 Cleaning Paper Feed Unit PF-602m	14
1.6 Cleaning Paper Feed Unit PF-707 or Paper Feed Unit PF-707m	18
1.7 Cleaning Large Capacity Unit LU-202m, Large Capacity Unit LU-202XL, or Large Capacity Unit LU- 202XLm	20
2 Both Sides Adjust	23
2.1 What is Both Sides Adjust?	23
2.2 Adjustment flow to use paper of a new brand, weight, or size	24
2.2.1 Adjustment Timing	24
2.2.2 Adjustment Order	24
2.3 Regular adjustment flow	25
2.3.1 Adjustment Timing	25
2.3.2 Adjustment Order	25
2.3.3 Periodical Both Sides Adjustment Function	26
2.4 Adjustment flow for each job	27
2.4.1 Adjustment Timing	27
2.4.2 Adjustment Order	27
2.5 How to Operate the Both Sides Adj. Item	28
2.5.1 Finely adjust the side guide plates of the paper tray (for PF-707/PF-707m/PF- 602m)	28
2.5.2 [Front] Adjustment	31
2.5.3 [Gap] Adjustment (Back side adjustment)	36
2.5.4 [Scan Meas.] Adjustment	41
2.5.5 [Rotate/Skew] Adjustment	51
2.5.6 [AutoMeasure] Adjustment	58
2.5.7 Registering Paper Profile	62
2.5.8 Back Side Fine Adjustment	64
2.5.9 [Periodical Both Sides Adj.]	69
3 Quality Adj.	73
3.1 Quality Adjustment for Image Controller IC-603/ Image Controller IC-605	73
3.2 Regular adjustment flow (Standard)	74
3.2.1 Adjustment timing	74
3.2.2 Adjustment sequence	74
3.3 Regular adjustment flow (High accuracy)	75
3.3.1 Adjustment Timing	75
3.3.2 Adjustment Order	75
3.4 Adjustment flow to use a new type of paper	76
3.4.1 Adjustment timing	76
3.4.2 Adjustment sequence	76
3.5 Adjustment Flow when changing the screen	77
3.5.1 Adjustment timing	77
3.5.2 Adjustment sequence	77
3.6 Details of quality adjustment items	78
3.6.1 Setting of the Custom Screen	78
3.6.2 [Gamma Automatic Adjustment]	80
Performing [Gamma Automatic Adj.]	80
3.6.3 [Density Balance Adjustment] (for i1Pro, i1Pro2, or i1iSisXL)	82
Saving the measured data of the density balance	90
3.6.4 [Density Balance Adjustment] (for FD-5BT)	92
3.6.5 Registering the adjusted value of the density balance in the machine	103
3.6.6 [Density Balance Auto. Adj.]	110
3.6.7 [Maximum Density Adjustment]	120
3.6.8 [Maximum Density Adjustment] (for i1Pro/i1Pro2)	121
3.6.9 [Maximum Density Adjustment] (for FD-5BT)	130
3.6.10 [Max. Density Auto Adj.]	138
3.6.11 Checking the Color Density Control Setting	141
3.6.12 [Color Density Manual Control]	144
3.6.13 About Controller Calibration	147
Executing Calibration	148
3.6.14 About Exact Color calibration	154
Executing Exact Color: Color Centro	155
Executing Exact Color: Touch panel	162
3.6.15 About G7 Calibration	165
Executing G7 Calibration: Color Centro	166
Executing G7 Calibration: Touch panel	172