Konica Minolta KIP 79 Series KIP 79 Series Hardware User Manual - Page 9

Chapter 1

Before Use

1-2

1. 1

Installation Requirements

The following conditions are required for installation of the equipment.

1. Power source should be rated as follows.

220V - 240V plus 6% or minus 10%, 50/60Hz, 16A or higher

2. The equipment must be on an exclusive circuit.

3. The outlet must be near the equipment and easily accessible.

I Norge: Kan kobles til IT strøm distribusjonssystemer.

1. Make sure to connect this equipment to a grounded outlet.

2. For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near

the equipment and shall be easily accessible.

1. The installation site must not have open flames, dust or ammonia gases.

2. The equipment must not be exposed to the air vents from air conditioners.

It may affect the image quality.

3. The equipment should not be exposed to the direct sunlight.

Please draw curtains to block any sunlight.

When you open the Upper Unit to remove a mis-feed, do not expose the

Photoconductive Drum to strong (intense) light as this will damage the Drum.

Ozone will be generated while this equipment is use, although the quantity generated is

within safe levels. (See certifications.)

Ventilate the room, if required.

The site temperature range = 10 to 32 degrees Centigrade, with the humidity between

15% to 85% RH. (NON-CONDENSING)

Keep the printer away from water sources, boilers, humidifiers or refrigerators.

Keep ample room around the equipment to ensure comfortable operation.

(Refer to the following figure.)

The equipment must be leveled and the floor strength must be ample to sustain the

weight of the equipment.

Printer

1702mm / 67”

725mm / 29”

Front : 800mm / 32” or larger

Rear : 800mm / 32” or larger

Right : 300mm / 12” or larger

Left : 50mm / 2” or larger

Section	Page
KIP 79 Series User Manual A.0	1
Safety Warning	4
WARNING	5
CAUTION	6
POWER CORD INSTRUCTION	7
Chapter 1 Before Use	8
1. 1 Installation Requirements	9
1. 2 Originals Prohibited from Duplication	10
1. 3 Features	11
1. 4 Specifications	12
1. 4. 1 Printer Part	12
1. 4. 2 Scanner Part (for MFP Model)	14
1. 5 Appearance	15
1. 5. 1 Front	15
1. 5. 2 Rear	16
1. 6 Specifications for Scan Original (for MFP Model)	17
1. 6. 1 Original Standards	17
1. 6. 2 Special Documents	17
1. 6. 3 “Do Not Scan” Originals	18
1. 7 Specifications for the Printing Media	21
1. 7. 1 Papers not available to use	21
1. 7. 2 Keeping the paper in the custody	22
1. 7. 3 Treatment against environmental condition	23
Chapter 2 Basic Operations	25
2. 1 Turning on the Printer	26
2. 2 Turning off the Printer	28
2. 3 Replacing Roll Media	29
2. 4 Replacing Toner Cartridge	37
2. 5 Placing Cut Sheet Media	41
2. 6 Copying (for MFP Model)	42
2. 7 Stop of Scan or Copy (for MFP Model)	45
2. 8 Dehumidifying Roll Media	46
Chapter 3 Error Correction	48
3. 1 Paper Jam	49
3. 1. 1 Roll Deck Section Jam(Deck 1, 2 Mis-feed )	50
3. 1. 2 Manual Feeder Section Jam(By-Pass Mis-feed, Registration Mis-feed)	52
3. 1. 3 Media Feed Section Jam(Mid Feed Mis-feed, Registration Mis-feed,Separation Mis-feed)	53
3. 1. 4 Fuser Section Jam (Exit Back Mis-feed)	56
3. 1. 5 Stack Jam	61
3. 1. 6 Original Jam (for MFP Model)	62
3. 2 Door Open	63
3. 2. 1 Roll Deck (Deck 1, 2 Open)	63
3. 2. 2 Upper Frame Unit / Top Cover(Front Cover Open)	64
3. 2. 3 Paper Exit Door (Paper Exit Door Open)	65
3. 2. 4 Scanner Unit (Scanner feeder open)(for MFP Model)	65
3. 3 Other Operator Call	66
3. 3. 1 Roll Replacement	66
3. 3. 2 Toner Empty	66
3. 4 Service Call Errors	67
Chapter 4 Maintenance	68
4. 1 Scanner Unit (for MFP Model)	69
4. 1. 1 Scan Glass, Feed Roller, Guide Plate	69
4. 1. 2 Sensor	72

Konica Minolta KIP 79 Series KIP 79 Series Hardware User Manual - Page 9

Installation Requirements

Page 9 highlights