Konica Minolta Kodak i1860 User Guide - Page 63

Replacing the rear blotter strips, before pressing the adhesive side into the channel.

Get Konica Minolta Kodak i1860 PDF manuals and user guides View all Konica Minolta Kodak i1860 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

Replacing the rear blotter strips Blotter strips collect ink overflow. They should be replaced when there is a build-up of ink. Replacement blotter strips may be purchased through your supplier. 1. Remove the output tray. The rear blotter strips are located in the two drawers underneath the baffle. 2. Open the one of the drawers by pushing it in a little and lifting up slightly, then pull it out. 3. Peel off the soiled blotter strip. 4. Peel the backing away from the new blotter strip. 5. Align the blotter strip in the channel. Be sure it is properly aligned before pressing the adhesive side into the channel. 6. Press the blotter strip firmly into place. 7. Repeat Steps 2 - 5 for the other blotter strip. 8. Close the drawer(s) by pushing it in and sliding it down slightly. This will lock the drawer in place. 9. Replace the output tray. A-61555 March 2007 4-11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
A-61555
March 2007
4-11
Replacing the rear
blotter strips
Blotter strips collect ink overflow. They should be replaced when there
is a build-up of ink. Replacement blotter strips may be purchased
through your supplier.
1.
Remove the output tray. The rear blotter strips are located in the two
drawers underneath the baffle.
2.
Open the one of the drawers by pushing it in a little and lifting up
slightly, then pull it out.
3.
Peel off the soiled blotter strip.
4.
Peel the backing away from the new blotter strip.
5.
Align the blotter strip in the channel. Be sure it is properly aligned
before pressing the adhesive side into the channel.
6.
Press the blotter strip firmly into place.
7.
Repeat Steps 2 - 5 for the other blotter strip.
8.
Close the drawer(s) by pushing it in and sliding it down slightly. This
will lock the drawer in place.
9.
Replace the output tray.