Konica Minolta Kodak i1860 User Guide - Page 85

Replacing the pre-separation pad, Replacing the imaging guides, on the guides.

Get Konica Minolta Kodak i1860 PDF manuals and user guides View all Konica Minolta Kodak i1860 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 85 highlights

Replacing the preseparation pad Change the pre-separation pad when the frequency of multi-fed documents increases. 1. Open the pod. 2. Remove the pre-separation pad by lifting the pad up and out of position. Replacing the imaging guides 3. Install the new pre-separation pad. Be sure it snaps into place. 4. Close the pod. The imaging guides should be replaced when they are heavily scratched and defects show in the image. NOTE: Handle the imaging guides carefully so as to not put fingerprints on the guides. 1. Open the pod. 2. Turn the screw on each end of the lower imaging guide to remove it from its position. 5-20 3. Install the new imaging guide and turn the screws to secure the imaging guide. 4. Repeat Steps 2 and 3 to replace the upper imaging guide. 5. Close the pod. A-61555 March 2007

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
5-20
A-61555 March 2007
Replacing the pre-
separation pad
Change the pre-separation pad when the frequency of multi-fed
documents increases.
1.
Open the pod.
2.
Remove the pre-separation pad by lifting the pad up and out of
position.
3.
Install the new pre-separation pad. Be sure it snaps into place.
4.
Close the pod.
Replacing the imaging
guides
The imaging guides should be replaced when they are heavily
scratched and defects show in the image.
NOTE: Handle the imaging guides carefully so as to not put fingerprints
on the guides.
1.
Open the pod.
2.
Turn the screw on each end of the lower imaging guide to remove it
from its position.
3.
Install the new imaging guide and turn the screws to secure the
imaging guide.
4.
Repeat Steps 2 and 3 to replace the upper imaging guide.
5.
Close the pod.