Konica Minolta bizhub 28e bizhub 28e PaperCut IU Embedded Manual - Page 14

Confirm that the jobs are held, by checking that the jobs are listed in the Printers -&gt

Get Konica Minolta bizhub 28e PDF manuals and user guides View all Konica Minolta bizhub 28e manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

4. Press "OK" or "Apply" to save the changes. All printing to this queue will now be held until released by a user. Make sure the copier is enabled as a "Print release": 1. In PaperCut, select the "Devices" tab. 2. Select the Konica Minolta device. 3. Under "Device function", make sure "Enable print release" is selected. If you have followed the installation steps from the previous chapter, this function will already be enabled. 4. Select the print queue that was enabled for hold/release above. The Konica Minolta device will allow jobs in the selected queues to be released. 5. Press "OK" to save. 6. Login to a computer workstation as 'testusersimple'. 7. Print a few jobs to the print queue that was configured above. The jobs will be held in the hold/release queue. 8. Confirm that the jobs are held, by checking that the jobs are listed in the "Printers -> Jobs Pending Release" page of the PaperCut administration interface. 9. Confirm that the username is 'testusersimple'. At the device: 1. Log in with the 'testusersimple' username and corresponding password, as in scenario 1. 2. The interface allows for print release to be done immediately after authenticating, without unlocking the device. Any held jobs will be shown in the print release screen. 3. A list of print jobs will show. You can highlight and deselect individual items by pressing the list item. 13 of 27 Copyright © 2019 KONICA MINOLTA BUSINESS SOLUTIONS U.S.A., INC. All Rights Reserved 06/2019

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
13 of 27
4.
Press “OK” or “Apply” to save the changes.
All printing to this queue will now be held
until released by a user.
Make sure the copier is enabled as a “Print release”:
1.
In PaperCut, select the “Devices” tab.
2.
Select the
Konica Minolta
device.
3.
Under “Device function”, make sure “Enable print release” is selected. If you have
followed the installation steps from the previous chapter, this function will already be
enabled.
4.
Select the print queue that was enabled for hold/release above.
The
Konica Minolta
device
will allow jobs in the selected queues to be released.
5.
Press “OK” to save.
6.
Login to a computer workstation as ‘testusersimple’.
7.
Print a few jobs to the print queue that was configured above.
The jobs will be held
in the hold/release queue.
8.
Confirm that the jobs are held, by checking that the jobs are listed in the “Printers ->
Jobs Pending Release” page of the PaperCut administration interface.
9.
Confirm that the username is ‘testusersimple’.
At the device:
1.
Log in with the ‘testusersimple’ username and corresponding password, as in
scenario 1.
2.
The interface allows for print release to be done immediately after authenticating,
without unlocking the device. Any held jobs will be shown in the print release screen.
3.
A list of print jobs will show. You can highlight and deselect individual items by
pressing the list item.
Copyright © 201
9
KONICA MINOLTA BUSINESS SOLUTIONS U.S.A., INC. All Rights Reserved
06/2019