Kyocera FS 1700 FS-1700/3700 Users Manual - Page 107

Withdrawing the Main Circuit Board from the Printer, Changing the Jumper Connector, eign objects

Get Kyocera FS 1700 - B/W Laser Printer PDF manuals and user guides View all Kyocera FS 1700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 107 highlights

C.2. RS-232C/RS-422A Interface *Withdrawing the Main Circuit Board from the Printer Be sure to remove the memory card first if inserted in the printer's memory card slot. Withdraw the main circuit board completely from the printer as follows: 1. Turn the printer's power off. Unplug the printer's power cable and disconnect the printer from the host computer. 2. Remove the three screws from the printer's rear cover. 3. Pull the main circuit board all the way out * of the printer. Before pulling the main board out, clean an area on the table, etc., at the back of the printer's rear panel. Foreign objects, accidentally sticking to the back of the main board, can cause serious damage to the printer. Changing the Jumper Connector 1. Carefully remove the jumper connector from the main circuit board, and reconnect to the pin position shown in the diagram. š Power OFF ( ) Jumper Connector Jumper Connector 2. After completion of the above, return the main circuit board to the printer by reversing the procedure followed when removing it. C-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
Withdrawing the Main Circuit Board from the Printer
Be sure to remove the memory card first if inserted in the printer’s memory
card slot.
Withdraw the main circuit board completely from the printer as follows:
1.
Turn the printer’s power off. Unplug the
printer’s power cable and disconnect the
printer from the host computer.
2.
Remove the three screws from the
printer’s rear cover.
3.
Pull the main circuit board all the way out
of the printer.
Before pulling the main board out,
clean an area on the table, etc., at the
back of the printer’s rear panel. For-
eign objects, accidentally sticking to
the back of the main board, can
cause serious damage to the printer.
Changing the Jumper Connector
1.
Carefully remove the jumper connector
from the main circuit board, and recon-
nect to the pin position shown in the dia-
gram.
2.
After completion of the above, return the main circuit board to the printer by reversing
the procedure followed when removing it.
Jumper Connector
Power OFF (
)
Jumper Connector
C.2.
RS-232C/RS-422A Interface
C-7