LG 42LH250H Owners Manual - Page 153

B-LAN, Overview

Get LG 42LH250H PDF manuals and user guides View all LG 42LH250H manuals
Add to My Manuals
Save this manual to your list of manuals

Page 153 highlights

B-LAN Overview B-LAN Setup and Overview Power to the B-LAN module is controlled by Installer Menu Item 118 Power savings. By default, value 003, the B-LAN module is only powered on when the TV is powered on. There are two bits in the Power Savings item to control power to the B-LAN module, one for power during TV Standby mode and one for power during TV Power On mode. When the bit is O, the B-LAN module is powered. When the bit is 1, the B-LAN module is not powered (Power Savings is Enabled). Power Saving 1 3 7 TV Standby State TV Power On State BLAN Power MPI Slot Power BLAN Power MPI Slot Power On Standby On Off Standby On Off Standby Off Main Main Main The B-LAN module is internal to the TV. It allows the Hotel/Institution headend equipment to communicate with the TV for configuration and control. This communication is via the institution'r RF distribution system. The control device at the headend (ex FMALG101) can control multiple TVs. When the TV is first installed, it must be powered on in order for the headend to be able to communicate with the B-LAN. At this point, if it is desired for the BLAN to always be powered on, particularly during Standby mode, the BLAN Standby Power Saving mode setting should be downloaded as Disabled. The new settings will not be active until the BLAN actually downloads the configuration data to the PTC and the PTC is reset. If it known that the application requires only using the MPI card slot and not the embedded BLAN, the installer can go into the Installer Settings menu and enable the BLAN Power Savings mode, in both Standby and TV power on. 206-4118 PA G E 4 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
B-LAN
Overview
B-LAN
Setup
and
Overview
Power to the
B-LAN module is controlled
by Installer
Menu
Item 118 Power savings.
By default,
value
003, the
B-LAN module is
only
powered
on when the
TV is powered on. There are two bits
in the Power Savings item
to control
power to the
B-LAN module,
one for power during
TV Standby mode and one for power during
TV Power On mode. When the
bit
is O, the
B-LAN module
is pow-
ered. When the
bit
is 1, the B-LAN module
is not powered
(Power Savings is Enabled).
TV Standby State
TV Power On State
Power Saving
BLAN Power
MPI Slot Power
BLAN Power
MPI Slot Power
1
On
Standby
On
Main
3
Off
Standby
On
Main
7
Off
Standby
Off
Main
The B-LAN module is internal
to the TV. It allows
the
Hotel/Institution
headend equipment
to communicate
with
the
TV for config-
uration
and control.
This communication
is via the
institution'r
RF distribution
system.
The control
device at the
headend
(ex FMA-
LG101) can control
multiple
TVs. When the TV is first
installed,
it must be powered on in order for the
headend to
be able to com-
municate
with
the
B-LAN. At this
point,
if it is desired for the
BLAN to always be powered on,
particularly
during
Standby
mode,
the
BLAN Standby
Power Saving mode setting
should
be downloaded
as Disabled. The new settings
will
not
be active
until
the
BLAN actually
downloads
the configuration
data to the
PTC and the
PTC is reset.
If it known
that
the
application
requires
only using
the
MPI card slot
and not the
embedded
BLAN, the
installer
can go into the
Installer
Settings
menu and enable
the
BLAN Power Savings mode, in both
Standby
and TV power
on.
206-4118
PAGE
45