LG DLG2532W Owners Manual - Page 12

Electric Dryers - dryer no heat

Get LG DLG2532W PDF manuals and user guides View all LG DLG2532W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Electric Dryers (120V/244) Volt, 60 Hertz, 3-Wire Installation) (120V/208 Volt, 61) Hertz, 3-Wire Installation) NOTE : The wMng diagram is located inside the control h{md. To reducd the risk of fire, electric shock, serious injury or death, all wiring and grounding MUST conform with the latest _ition of the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22A, and such local regulations as might apply. It is the E customer's responsibility to have the wiring and fuses checked by a qualified electrician to make sure your home has im adequate electrical power to operate the Grounding Instructions • This duer must be connected to a grounded metal, permanent wiring system; or an equipmeni:-grounding couduclor must _ run with the circuit conductors and connected to the equipment-grounding terminal or lead on the dryer. O The dryer has its own _cnninal block Ihat must be connected to a sepa'ate branch, 60/lertz, single phase: circuit, AC (alter_mting current) circuit, tilsed at: 30 Amperes (the circuit must be fused on N)th sides of the liue). ELECTRICAL SERVICE FOR THE DRYER SIIOI?LD BE OF MAXIMUM RATE VOLTAGE LISTED ON THE NAMEPLATE. DO NOT CONNECT DRYER TO 110, 115, OR 120 VOLT CIRCI!IT. Heating elements are available for :field ins{allation in dryers which are to be conected m electrical service of dift;crent w)lmge than that listed on namq_late, such as 208 Volt. O If branch circuit m dryer is fifteen i)et (4.50 m) or less in length, u_= U.L. (Underwriters LaN_ratories) listed No. 10 A.W.G. wire (copper wire only), or as rcqaircd by local c(_es. If over fifteen tibet (4.50 in), use [J.L. (Underwriters I.abomtories) listed No. 8 A.W.G. wire (copper wire only), or as l_.Nuiredby local codes. Allow sufficient slack in wiring _ dryer can be moved from its normal location when necess_uLv. O The ln)wer cord (pigtail) conn_tion between wall receptacle and dryer terminal block IS NOT supplic-d with dryer. Type of pigtail and gauge of wire must confom_ to local codes and with instructions mentioned on the :li:)llowingpages. O The meth(x.t of wiring the dryer is optional and subject to k_'a! c_e requirements_ Ret'er to examples on next page. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
E
im
Electric Dryers
(120V/244) Volt, 60 Hertz, 3-Wire
Installation)
(120V/208
Volt, 61) Hertz, 3-Wire
Installation)
NOTE
: The
wMng
diagram
is
located
inside the
control h{md.
To reducd
the risk of fire,
electric
shock,
serious
injury
or death,
all wiring
and
grounding
MUST
conform
with the latest
_ition
of the National
Electrical
Code,
ANSI/NFPA
70, or the Canadian
Electrical
Code, CSA
C22A,
and such
local
regulations
as
might
apply.
It is the
customer's
responsibility
to have the
wiring
and
fuses
checked
by a qualified
electrician
to make
sure your
home
has
adequate
electrical
power
to operate
the
Grounding
Instructions
•
This duer
must be connected
to a grounded
metal,
permanent
wiring system; or an equipmeni:-grounding
couduclor
must _
run with
the
circuit conductors
and
connected
to the equipment-grounding
terminal
or
lead
on the dryer.
O
O
O
O
The dryer has its own _cnninal block Ihat must be
connected
to a sepa'ate
branch, 60/lertz,
single phase:
circuit, AC (alter_mting current) circuit, tilsed at: 30
Amperes (the circuit must be fused on N)th sides of
the liue). ELECTRICAL
SERVICE
FOR THE
DRYER
SIIOI?LD
BE OF MAXIMUM
RATE
VOLTAGE
LISTED
ON
THE
NAMEPLATE.
DO
NOT
CONNECT
DRYER
TO
110, 115, OR 120
VOLT CIRCI!IT.
Heating elements
are
available
for
:field ins{allation in dryers which are to be conected
m
electrical
service of dift;crent w)lmge than that listed
on namq_late,
such as 208 Volt.
If branch circuit
m dryer is fifteen i)et
(4.50 m) or
less in length, u_= U.L. (Underwriters
LaN_ratories)
listed No. 10 A.W.G. wire (copper wire only), or as
rcqaircd by local c(_es.
If over fifteen tibet
(4.50
in),
use
[J.L.
(Underwriters
I.abomtories)
listed
No.
8
A.W.G. wire (copper wire only), or as l_.Nuiredby
local codes. Allow sufficient
slack in wiring _
dryer
can be moved from its normal location
when
necess_uLv.
The ln)wer cord (pigtail) conn_tion
between
wall
receptacle
and
dryer terminal
block IS NOT
supplic-d
with dryer.
Type of pigtail and gauge of wire must
confom_ to local codes
and
with instructions
mentioned
on the :li:)llowingpages.
The meth(x.t of wiring the dryer is optional and
subject to k_'a! c_e
requirements_ Ret'er
to
examples
on next page.
12