Lantronix UDS-10 UDS-10 / UDS100 - User Guide - Page 33

Disconnect Mode, Flush Mode - password

Get Lantronix UDS-10 PDF manuals and user guides View all Lantronix UDS-10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

UDS10/UDS100 User Guide Configuring the UDS Using Telnet or the Serial Port Disconnect Mode This option determines the conditions under which the unit causes a network connection to terminate. In DisConnMode, DTR drop either drops the connection or is ignored. Note: To look up hex values, see B: Binary to Hexadecimal. Table 5-9. Disconnect Mode Options Disconnect Mode Option Bit 7 6 5 4 3 2 1 0 Disconnect with DTR drop 1 Ignore DTRa Telnet mode and terminal type setup1 Channel (port) password2 Hard disconnect3 0 1 1 0 Disable hard disconnect State LED off with connection4 Disconnect with EOT (^D)5 1 1 1 1. The UDS sends the "Terminal Type" upon an outgoing connection. 2. A password is required for a connection to the serial port from the network. 3. The TCP connection closes even if the remote site does not acknowledge the disconnection. 4. When there is a network connection to or from the serial port, the state LED turns off instead of blinking. 5. When Ctrl D or Hex 04 are detected, the connection is dropped. Both Telnet mode and Disconnect with EOT must be enabled for Disconnect with EOT to function properly. Ctrl D is only be detected going from the serial port to the network. Flush Mode Flush Mode (buffer flushing) controls line handling and network buffers with connection startup and disconnect. You can select between two different packing algorithms. Note: To look up hex values, see B: Binary to Hexadecimal. Available Flush Mode options are: Table 5-10. Flush Mode Options Function Bit 7 6 5 4 3 2 1 0 Input Buffer (Serial to Network) Clear with active connection (from serial) 1 Clear with passive connection (from network) 1 Clear with disconnect 1 Output Buffer (Network to Serial) Clear with active connection (from serial) 1 Clear with passive connection (from network) 1 Clear with disconnect 1 Alternate Packing Algorithm (Pack Control) Enable 1 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
UDS10/UDS100 User Guide
Configuring the UDS Using Telnet or the Serial Port
33
Disconnect Mode
This option determines the conditions under which the unit causes a network
connection to terminate. In DisConnMode, DTR drop either drops the connection or is
ignored.
Note
:
To look up hex values, see
B: Binary to Hexadecimal
.
Table 5-9. Disconnect Mode Options
Disconnect Mode Option
Bit 7
6
5
4
3
2
1
0
Disconnect with DTR drop
1
Ignore DTRa
0
Telnet mode and terminal type setup
1
1
Channel (port) password
2
1
Hard disconnect
3
0
Disable hard disconnect
1
State LED off with connection
4
1
Disconnect with EOT (^D)
5
1
1.
The UDS sends the "Terminal Type" upon an outgoing connection.
2. A password is required for a connection to the serial port from the network.
3. The TCP connection closes even if the remote site does not acknowledge the
disconnection.
4. When there is a network connection to or from the serial port, the state LED
turns off instead of blinking.
5. When Ctrl D or Hex 04 are detected, the connection is dropped. Both Telnet
mode and Disconnect with EOT must be enabled for Disconnect with EOT to
function properly. Ctrl D is only be detected going from the serial port to the
network.
Flush Mode
Flush Mode (buffer flushing) controls line handling and network buffers with
connection startup and disconnect. You can select between two different packing
algorithms.
Note
:
To look up hex values, see
B: Binary to Hexadecimal
.
Available Flush Mode options are:
Table 5-10. Flush Mode Options
Function
Bit 7
6
5
4
3
2
1
0
Input Buffer (Serial to Network)
Clear with active connection (from serial)
1
Clear with passive connection (from network)
1
Clear with disconnect
1
Output Buffer (Network to Serial)
Clear with active connection (from serial)
1
Clear with passive connection (from network)
1
Clear with disconnect
1
Alternate Packing Algorithm (Pack Control)
Enable
1