Home » Lantronix Manuals » Electronics Accessories » Lantronix UDS-10 » Manual Viewer

Lantronix UDS-10 UDS-10 / UDS100 - User Guide - Page 71

Active connection, Passive connection, Disconnect, Enable

Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

UDS10/UDS100 User Guide Binary to Hexadecimal Conversions Flush Mode Options Serial to Network Network to Serial Clear input buffer upon: Active connection Passive connection Disconnect Active connection Passive connection Active connection Passive connection Disconnect Active connection Disconnect Passive connection Disconnect Active connection Passive connection Disconnect Clear output buffer upon: Active connection Passive connection Disconnect Active connection Passive connection Disconnect Active connection Passive connection Disconnect Active connection Passive connection Disconnect Active connection Passive connection Disconnect Active connection Passive connection Disconnect Active connection Passive connection Disconnect Active connection Passive connection Disconnect Active connection Passive connection Disconnect Alternate Packing Algorithm Enable Enable Enable Enable Enable Enable Enable Enable Hex 77 87 97 A7 B7 C7 D7 E7 F7 71

Section	Page
Contacts	2
Figures	6
Tables	7
Using This Guide	8
Purpose and Audience	8
Chapter Summary	8
Additional Documentation	9
Introduction	10
Applications	10
Application Examples	10
Protocol Support	12
Additional Features	12
Configuration Methods	12
Product Information Label	13
Getting Started	14
Installing the UDS	14
Required Information	15
Hardware Address	15
IP Address	15
Assigning the IP Address and Related Network Settings	16
DeviceInstaller	16
Serial Port Login	17
Configuring the UDS Using Web Manager	18
Accessing Web Manager	18
Using Web Manager	20
Example	20
Configuring the UDS Using Telnet or the Serial Port	22
Using a Telnet Connection	22
Using the Serial Port	23
Server Configuration (Network Configuration)	24
IP Address	24
Set Gateway IP Address	24
Netmask	24
Change Telnet configuration password	25
DHCP Naming	25
Channel 1 Configuration (Serial Port Settings)	26
Baudrate	26
I/F (Interface) Mode	26
Flow	27
Port Number	27
Connect Mode	28
Manual Connection	29
Remote IP Address	32
Remote Port	32
Disconnect Mode	33
Flush Mode	33
Pack Control	34
Disconnect Time (Inactivity Timeout)	35
Send Characters	35
Telnet Terminal Type	35
Channel (Port) Password	35
Expert Settings	35
TCP Keepalive time in s	36
ARP Cache timeout in s	36
Security Settings	36
Disable SNMP	36
SNMP Community Name	37
Disable Telnet Setup	37
Disable TFTP Firmware Upgrade	37
Disable Port 77FE (Hex)	37
Disable Web Setup	37
Disable ECHO Ports	37
Enable Enhanced Password	37
Factory Default Settings	38
Channel 1 Configuration Defaults	38
Expert Settings Defaults	38
Security Settings Defaults	38
Exit Configuration Mode	38
Updating Firmware	39
Obtaining Firmware	39
Reloading Firmware	39
Using DeviceInstaller	39
Using TFTP	40
Using Another Unit	41
Using the Serial Port	41
Using Monitor Mode	43
Entering Monitor Mode Using the Serial Port	43
Entering Monitor Mode Using the Network	43
Using Monitor Mode Commands	44
Troubleshooting and Contact Information	45
LEDs	45
Problems and Error Messages	46
Technical Support	49
Connections and Pinouts	51
Serial Port	51
Serial Connector Pinouts	51
Null-Modem Cable	53
Network Port	53
Ethernet Connector Pinouts	54
Technical Specifications	55
UDS10 Technical Specifications	55
UDS100 Technical Specifications	56
Alternative Ways to Assign an IP Address	57
DHCP	57
AutoIP	57
BOOTP	58
ARP and Telnet	58
Binary to Hexadecimal Conversions	59
Converting Binary to Hexadecimal	59
Conversion Table	59
Scientific Calculator	60
Connect Mode Options	61
Disconnect Mode Options	64
Flush Mode Options	66
Interface Mode Options	72
Pack Control Options	73
Declaration of Conformity	75
Warranty	76