Lantronix XPort Pro XPort Pro - Command Reference - Page 106

Sets the Modbus Response Timeout in milliseconds., Restores the default Modbus Response Timeout.

Get Lantronix XPort Pro PDF manuals and user guides View all Lantronix XPort Pro manuals
Add to My Manuals
Save this manual to your list of manuals

Page 106 highlights

show show history show statistics soj disable soj enable soj text binary soj text set terminal terminal network test print tunnel write modbus (modbus) level commands additional port clrscrn default response timeout exit kill connection no additional port response timeout rss show show connections show history show statistics tcp server state disable tcp server state enable write modem (tunnel-modem:1) level commands clrscrn connect string default incoming connection default response type display remote ip disable XPort Pro Command Reference 5: Commands and Levels Displays the current configuration. Displays the last 20 commands entered during the current CLI session. Displays statistics and status information for this lpd line. Disables sending the start-of-job string after each print job. Enables sending the start-of-job string after each print job. Sets the start-of-job text allowing for binary characters. = string in binary format that will be sent to the printer at the beginning of each print job. Within [] use binary decimal up to 255 or hex up to 0xFF. Sets the start-of-job text. = ascii string that will be sent to the printer at the beginning of each print job. Enters the configure-terminal level. = number of the terminal line (serial port) to be configured. Enters the configure-terminal level for the network. Prints lines of text directly to the lpd line. = number of lines to print. Enters the tunnel level. = number of the tunnel line (serial port) to be configured. Stores the current configuration in permanent memory. Sets an additional TCP server port. Clears the screen. Restores the default Modbus Response Timeout. Exits to the config level. Kills modbus connection selected by index from show connections. Removes the additional TCP server port. Sets the Modbus Response Timeout in milliseconds. Enters the next lower level. Displays the current configuration. Displays connections. Displays the last 20 commands entered during the current CLI session. Displays statistics. Disables the Modbus TCP Server. Enables the Modbus TCP Server. Stores the current configuration in permanent memory. Clears the screen. Sets the CONNECT string used in modem emulation. = connect string. Default disables incoming network connections. Default uses text type responses. The incoming RING has nothing following it. 106

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
5: Commands and Levels
XPort Pro Command Reference
106
show
Displays the current configuration.
show history
Displays the last 20 commands entered during the current
CLI session.
show statistics
Displays statistics and status information for this lpd line.
soj disable
Disables sending the start-of-job string after each print job.
soj enable
Enables sending the start-of-job string after each print job.
soj text binary
<binary>
Sets the start-of-job text allowing for binary characters.
<binary> = string in binary format that will be sent to the
printer at the
beginning of each print job.
Within [] use binary decimal up to 255 or hex up to 0xFF.
soj text set
<text>
Sets the start-of-job text.
<text> = ascii string that will be sent to the printer at the
beginning of
each print job.
terminal
<line>
Enters the configure-terminal level.
<line> = number of the terminal line (serial port) to be con-
figured.
terminal network
Enters the configure-terminal level for the network.
test print
<number of lines>
Prints lines of text directly to the lpd line.
<number of lines> = number of lines to print.
tunnel
<line>
Enters the tunnel level.
<line> = number of the tunnel line (serial port) to be confi-
gured.
write
Stores the current configuration in permanent memory.
modbus (modbus) level commands
additional port
<number>
Sets an additional TCP server port.
clrscrn
Clears the screen.
default response timeout
Restores the default Modbus Response Timeout.
exit
Exits to the config level.
kill connection
<index>
Kills modbus connection selected by index from show
connections.
no additional port
Removes the additional TCP server port.
response timeout
<milliseconds>
Sets the Modbus Response Timeout in milliseconds.
rss
Enters the next lower level.
show
Displays the current configuration.
show connections
Displays connections.
show history
Displays the last 20 commands entered during the current
CLI session.
show statistics
Displays statistics.
tcp server state disable
Disables the Modbus TCP Server.
tcp server state enable
Enables the Modbus TCP Server.
write
Stores the current configuration in permanent memory.
modem (tunnel-modem:1) level commands
clrscrn
Clears the screen.
connect string
<text>
Sets the CONNECT string used in modem emulation.
<string> = connect string.
default incoming connection
Default disables incoming network connections.
default response type
Default uses text type responses.
display remote ip disable
The incoming RING has nothing following it.