Lenovo NetVista (English) Quick reference guide - Page 33

Troubleshooting and diagnostics, Basic troubleshooting

Get Lenovo NetVista PDF manuals and user guides View all Lenovo NetVista manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Chapter 4. Troubleshooting and diagnostics This chapter describes some basic troubleshooting and diagnostic tools. If your computer problem is not described here, use Access IBM for more detailed troubleshooting information. Basic troubleshooting Symptom Action The computer does not Verify that: start when you press the v The power cord is plugged into the rear of the computer power button. and into a working electrical outlet. v If your computer has a secondary power switch on the back of the computer, ensure that it is switched on. Check the power indicator on the front of the computer to ensure that the power is on. The monitor screen is blank. If you cannot correct the problem, have the computer serviced. Verify that: v The monitor cable is securely attached to the rear of the monitor and to the rear of the computer. v The monitor power cord is plugged into the monitor and into a working electrical outlet. v The monitor is turned on, and the brightness and contrast controls are set correctly. v The monitor signal cable is securely connected to the monitor and to the monitor connector on the computer. Note: If your computer has two monitor connectors, verify that your monitor is connected to the one in the accelerated graphics port (AGP) option slot rather than the one in the rear of the system board. See Step 5 on page 6. If you cannot correct the problem, have the computer serviced. © Copyright IBM Corp. 2002 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
Chapter 4. Troubleshooting and diagnostics
This chapter describes some basic troubleshooting and diagnostic tools. If your
computer problem is not described here, use Access IBM for more detailed
troubleshooting information.
Basic troubleshooting
Symptom
Action
The computer does not
start when you press the
power button.
Verify that:
v
The power cord is plugged into the rear of the computer
and into a working electrical outlet.
v
If your computer has a secondary power switch on the
back of the computer, ensure that it is switched on. Check
the power indicator on the front of the computer to ensure
that the power is on.
If you cannot correct the problem, have the computer
serviced.
The monitor screen is
blank.
Verify that:
v
The monitor cable is securely attached to the rear of the
monitor and to the rear of the computer.
v
The monitor power cord is plugged into the monitor and
into a working electrical outlet.
v
The monitor is turned on, and the brightness and contrast
controls are set correctly.
v
The monitor signal cable is securely connected to the
monitor and to the monitor connector on the computer.
Note:
If your computer has two monitor connectors, verify
that your monitor is connected to the one in the accelerated
graphics port (AGP) option slot rather than the one in the
rear of the system board. See Step 5 on page 6.
If you cannot correct the problem, have the computer
serviced.
© Copyright IBM Corp. 2002
19