Lenovo PC 300PL Installing Options in your PC300PL - 6592 - Page 87

Configuring an ISA Legacy Adapter

Get Lenovo PC 300PL PDF manuals and user guides View all Lenovo PC 300PL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 87 highlights

Configuring an ISA Legacy Adapter To configure an installed ISA legacy adapter, you might need to alter switch or jumper settings on the adapter. If there is a conflict, you must use the Configuration/Setup Utility program to set the ISA legacy resource information, such as memory locations, I/O assignments, and DMA and interrupt assignments. Note: For more information about required resources and switch settings, refer to the documentation that comes with the adapter. To set the legacy resource information for an installed adapter: 1 Start the Configuration/Setup Utility program (see "Starting the Configuration/Setup Utility Program" on page 70). 2 Select ISA Legacy Resources from the Configuration/Setup Utility menu. 3 As needed, select Memory Resources, I/O Port Resources, DMA Resources, or Interrupt Resources. 4 Set the appropriate resource to Not available. 5 Press Esc to return to the main menu. 6 Select Save Settings and press Enter. If you remove an ISA legacy adapter, you must reset to Available the system resources that are no longer being used. To do this, follow the above procedures and select Available at step 4. Note: For more information on adapters and resolving conflicts, see "Adapter Configuration" on page 33 and Appendix B, "Interrupt and DMA Resources" on page 78. Chapter 7. Completing the Installation 73

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
Configuring an ISA Legacy Adapter
To configure an installed ISA legacy adapter, you might need to alter switch or
jumper settings on the adapter.
If there is a conflict, you must use the
Configuration/Setup Utility program to set the ISA legacy resource information,
such as memory locations, I/O assignments, and DMA and interrupt assignments.
Note:
For more information about required resources and switch settings, refer to
the documentation that comes with the adapter.
To set the legacy resource information for an installed adapter:
1
Start the Configuration/Setup Utility program (see “Starting the
Configuration/Setup Utility Program” on page
70).
2
Select
ISA Legacy Resources
from the Configuration/Setup Utility menu.
3
As needed, select
Memory Resources, I/O Port Resources, DMA Resources,
or
Interrupt Resources
.
4
Set the appropriate resource to
Not available
.
5
Press
Esc
to return to the main menu.
6
Select
Save Settings
and press
Enter
.
If you remove an ISA legacy adapter, you must reset to
Available
the system
resources that are no longer being used.
To do this, follow the above procedures
and select
Available
at step 4.
Note:
For more information on adapters and resolving conflicts, see “Adapter
Configuration” on page
33 and Appendix
B, “Interrupt and DMA
Resources” on page
78.
Chapter
7.
Completing the Installation
73